core clad 中文意思是什麼

core clad 解釋
磁芯敷層
  • core : CORE ＝Congress of Racial Equality 〈美國〉爭取種族平等大會。n 1 果心。2 （事物、問題等的）中心，...
  • clad : adj. 1. 穿衣的。2. 被覆蓋的。3. 鍍過（另一種）金屬的；用金屬包被的。vt. （clad; cladding） 在（金屬）外麵包上另一種金屬。
  1. Epoxide cellulose paper core, glass cloth surfaces copper - clad laminates

    環氧玻璃布紙復合覆銅箔板
  2. Using double - clad fibers, an efficient coupling of a high - power pump source into a single - mode fiber core can be achieved

    尤其是包層泵浦技術的應用，使高功率輸出的光纖激光器實現成為可能。
  3. Base materials for printed circuits - epoxide cellulose paper core, epoxide glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test

    印製電路的基體材料.環氧纖維素紙芯，限定易燃性的
  4. Metal core copper - clad laminate

    金屬芯覆銅箔層壓板
  5. . 3 base materials for printed circuits ; part 2 : specifications ; specification 9 : epoxide cellulose paper core, epoxide glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test ; amendment 3

    印製電路用基材.第2部分:規范.第9號規范:易燃的具有環氧纖維紙芯且表面覆銅的環氧玻璃布層壓板
  6. From the theoretic analyses, we draw the conclusion that the pump power can be heighten by adopting the eccentric core double - clad fiber. and we put forward a new coupling technology : micro - prism technology

    通過理論分析得出了用偏芯型雙包層光纖可以進一步提高泵浦功率的結論。並提出了一種新型的泵浦光耦合技術：微型棱鏡技術。
  7. Base materials for printed circuits - part 2 : specifications - specification no 9 : epoxide cellulose paper core, epoxyde glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test

    印刷電路用基材.第2部分:規范. 9號規范.規定易燃性的環氧化合物纖維素紙芯環氧化合物玻璃布麵包銅層壓板
  8. Base materials for printed circuits. part 2 : specifications. specification number 9 : epoxide cellulose paper core, epoxyde glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test

    印刷電路用基材.第2部分:規范. 9號規范:規定易燃性的環氧化合物纖維素紙芯環氧化合物玻璃布麵包銅層壓板
  9. Base materials for printed circuits ; part 2 : specifications ; specification no. 9 : epoxide cellulose paper core, epoxide glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test

    印製電路用基材.第2部分:規范.第9號規范:規定易燃性的環氧化合物纖維素紙芯的環氧化合物玻璃布表面覆銅層壓板
  10. . 5 base materials for printed circuits - part 2 : specifications ; specification no. 9 : epoxide cellulose paper core, epoxide glass cloth surfaces copper - clad laminated sheet of defined flammability vertical burning test ; amendment 5

    印製電路用基材.第2部分:規范.第9號規范:規定易燃性的環氧化合物纖維素紙環氧玻璃布表面銅覆層壓板
  11. The term of mode - filtered light refers to the observation that light initially propagating down an optical fiber can be decoupled from that fiber by increasing the cladding ri at the core / clad interface with a permeating analyte, thus changing the allowable propagating modes within the fiber, resulting in a continuous and nearly linear increase in mode - filtered light with increasing cladding ri

    所謂模式濾光，是指分析對象進入光纖包層引起光纖芯包界面的折射率增加，導致光纖內的部分傳導模不滿足傳導條件而從光纖的包層中側漏出來的光學信號，它與包層折射率的增量在一定條件下線性相關。
  12. Standard specification for aluminum - clad steel core wire for aluminum conductors, aluminum - clad steel reinforced

    包鋁鋼芯加強的鋁導線用包鋁鋼芯線的標準規范
  13. A laser diode with 976nm center wavelength and 2. 03w maximum cw output power is pumping unidirectionally through the couple - imaging system on a double - clad yb - doped silica fiber with a yb - concentration 0. 65 mol % circular inner core, a d - shaped inner clad, and 15m length by f - b cavity. the center wavelength of the fiber laser is 1130nm, and the maximum cw output power is 130. 7mw. an optical - to - optical conversion efficiency of 42 % and a slope efficiency of 63. 4 % are obtained

    用中心波長976nm 、最大連續輸出功率為2 . 03w的ld泵浦源，通過成像耦合系統，單端直腔式泵浦纖芯摻雜濃度為0 . 65mol % 、內包層截面形狀為d形、長度為15米的雙包層摻鐿石英光纖，實現了中心波長1130nm 、最大功率為130 . 7mw的連續激光輸出，光纖激光器的光光效率為42 . 0 % ，斜效率達到63 . 4 % 。
分享友人
分享到 Line

分享到臉書