coupling axis 中文意思是什麼
coupling axis
解釋
接頭軸心-
Some of them are of advanced ones, such as 5 - face grinding machine, electronic beam perforator, vacuum brazing equipment, curvic coupling grinding machine, controlled atmospheric quenching over, 4 - axis and 5 - axis nc milling machines, equipment for multi - component impregnation, heavy - duty grinder and high speed broacher, etc
擁有先進的五面磨床電子束打孔真空釬焊圓弧端磨可控氣氛淬火爐和四軸五軸數控銑床以及多元共滲強力磨削快速拉削等一批先進加工設備。 -
The result of optimization and analysis show : 1 ) across - axis sensitivity is smaller, less than 2 % of the primary axis sensitivity ; 2 ) the first mode is dominant at primary axis, which reduce intersectional coupling ; 3 ) when damp ratio is between 0. 3 and 0. 7, accelerometer has better dynamic characteristic
分析結果表明此種結構的具有： 1 ）橫向靈敏度小， x 、 z方向的橫向靈敏度均不到敏感方向的2 ； 2 ）在敏感方向上，一階模態起主導作用，其它模態的影響較小，有利於減小交叉耦合的影響； 3 ）當阻尼比毛為0 . 3 ? 0 . 7時，傳感器具有較好的動態特性。 -
In the former, two computing modes of fem are built, aimed at the coupling of variable - profile pylon, curved - axis arch and flexible cable. the software algor feas is used to get the results of dynamic numerical analysis, such as natural vibration frequency, vibration mode, dynamic displacement, dynamic stress, which are compared with the results of shaking table test research to draw to important conclusions. these conclusions provide not only potent basis for the design and construction of nanjing century tower, but also reference for other pylon - cable - arch structures similar to the project
在動態數值分析中，針對世紀塔變截面的塔身，曲線軸線的拱以及柔性拉索相互耦合時清況，建立兩種有限元計算模式，利用有限元軟體algorfeas得到動力數值分析的結果，如：自振頻率、振型、動位移、動應力等等，再和振動臺試驗研究成果作比較，得到一些重要的結論，從而為南京世紀塔工程的設計和施工提供強有力的依據，而且為類以於世紀塔工程的其它塔-索-拱結構的設計也提供一定的參考。 -
4. a novel three spring - mass structure is designed to close off the cross - axis coupling, the simplified dynamics model of which is worked out
4 .針對機械耦合誤差，提出了一種隔離耦合的三質量塊結構，建立了該結構的簡化動力學模型。 -
The speed reducer upper on the main machine makes central axis rotate through shaft coupling, and roller hanger rotates with central axis, and rollers on the hanger roll around the inside of ring
安裝在主機頂部的減速機，通過聯軸器連接中心軸旋轉，中心軸帶動磨輥吊架旋轉，磨輥裝在吊架上沿磨環內周一起滾動。 -
The speed reducer upper installed on the main machine makes central axis rotate through shaft coupling, and roller hanger rotates with central axis, and rollers on the hanger roll around the inside of ring
安裝在主機頂部的減速機，通過聯軸器連接中心軸旋轉，中心軸帶動磨輥吊架旋轉，磨輥裝在吊架上沿磨環內周一起滾動。 -
Because there are frequent failures in the connection method which uses crosshead intermediate axle shaft to join the relevant oart in the axis system of transmission system coupling this article suggests to use copper sliding pieces type transmission to increase the life of the middle axle system in transmission
摘要針對主傳動中間軸系統採用十字頭聯軸器與相關件連接方式，故障較多，改進為銅滑塊式傳動，提高了主傳動中間軸系統的壽命。 -
Because numerous mega - columns and mega - beams of mega - frame are thin - walled beam, hence the torsion can " t be neglected in structural calculation, and so in the calculation of structural overall stability, the coupling of bend and torsion can " t be neglected. the second is the thin - walled beam with opening section element which be considered effect of axis force and the coupling of bend and torsion
由於巨型結構中許多巨型柱和巨型梁為薄壁桿件，所以在結構計算中就不能忽略扭轉，同樣在結構的整體穩定性計算方面就必須考慮彎曲與扭轉的耦合，所以作者推導了開口薄壁桿件在考慮軸力效應、彎曲與扭轉耦合時的單元。 -
It shows that when wave propagates along axis direction, the displacements of radial, axis direction and the change of electric field are coupling each other, and there is dispersing phenomenon, and the displacement of circle direction can figure out independently, it has not dispersing phenomenon
發現當波沿著圓柱殼體軸向傳播時，物質的徑向運動軸向運動和電勢的變化相互耦合，伴有頻散現象但是扭轉運動可以獨立表示，並且同電場無關，無頻散現象。 -
I believe it says the power coupling on the negative axis has been polarized
我想它是想說負軸上的電源耦合器被極化了
分享友人