crane system 中文意思是什麼
crane system
解釋
克蘭叫牌法-
Finally, the controller working based on the combination of rbf neural networks and traditional pid control was applied to in aclinic kinetic machinery and lifting machinery of tower crane. the simulation of this controller was made using matlab, and the simulation results showed that the control system has some merits, such as quick response, little overshoot, well anti - jamming capacity, and little steady - state error, etc. both the dynamic property and static characteristic of this controller are better than traditional pid controller, and meet the tower crane
應用matlab對塔機的變幅和起升機構的運動控制進行模擬，模擬結果表明基於rbf神經網路整定pid的控制系統具有響應快、超調小及穩態誤差小等優點，其動、靜態性能優于單一pid控制，從而提高了塔式起重機工作機構的工作性能。 -
The application of plc to technological transformation of bridge crane electric control system
在行車電控系統技術改造的應用 -
Electronic control transmission system on tr - 250 tadano crane
250吊車上的電控變速系統 -
From them, the article gives the definitions of the kickstand crane and its parts function, sorts out and arranges them. at the some times, it also gives crane ' s function system chart. on the base of analyzing the chart, the article constructs the crane ' s technological function matrix and get ready for the future research
第二章中簡要介紹了功能論的思想和方法及門座起重機結構和用途，在功能設計法的理論基礎上，對門座起重機的總體和各部件進行了功能定義、功能分類和功能整理，並做出了門座起重機功能系統圖，在分析功能系統圖的基礎上，構造出門座起重機功能技術矩陣，為以後進一步研究作好準備。 -
Auto - control system design of lopsided moment tower crane
塔機不平衡力矩自動控制系統的設計 -
A new - type quayside container crane with jib - bridge luffing system as the main working part is brought out
摘要提出一種以臂橋架變幅系統為主要工作機構的岸邊集裝箱起重機。 -
Modal analysis of eot crane ' s steel rope system
橋式起重機鋼絲繩系統的模態分析 -
System of overhead traveling crane parametric design
橋式起重機橋架的參數化設計 -
Exploitation of vr training system for tower crane
塔式起重機模擬訓練器的研製 -
The results of experiments have show that electro - hydraulic proportional control system and its core controller of the auto crane ’ s performance are satisfied. it has the advantage of easily using and low cost, then it is worthy of further developing
核心控制器樣機的試驗情況表明，本文所設計的汽車起重機電液比例控制系統具有簡潔實用、成本低廉的優點，證明了本文研發成果的有效性和實用價值，為產品的產業化開發打下了良好的基礎。 -
The ideas of object - oriented technology and parametric design computation are combined to construct this parametric design system of overhead crane based on object - oriented technology. the corresponding technology are fully used to design and compute partial mechanism of overhead crane. this system makes the deviser ' s design convenient and design period is shortened, and in the meantime work efficiency is improved
基於面向對象技術的起重機參數化設計系統結合面向對象技術和參數化設計計算的思想，充分利用各相關技術，對橋式起重機部分機構進行設計計算，方便設計人員設計，縮短了設計周期，提高了工作效率。 -
Design of tower crane ' s complete frequency changing system
塔式起重機變頻成套系統設計 -
Application of a two - stage fuzzy pattern recognition model to the judgment of the main parameters selection in a crane system
兩級模糊模式識別模型及在起重機機構系列主參數擇優中的應用 -
Dynamic test has been performed on three strengthened girders after they were being put into service. according to the measured data from the dynamic test and the calculated results of the proportion of the load distribution on steel diagonal braces and steel crane girders as well as the increased carrying capacity after strengthening in consideration of the principle of cooperative work between braces and crane girders, the feasibility, rationality, and economy of this strengthening scheme have been verified. this scheme can be applied extensively to strengthen crane girders system including concrete crane girders system hereafter
最後結合對已經加固施工並投產使用的3榀鋼吊車梁的現場實際動測結果，按考慮下部鋼斜撐與鋼吊車梁二者協同工作的原理對鋼吊車梁與下部斜撐之間的荷載分配比例以及加固后鋼吊車梁的承載能力進行了進一步的計算驗證和對比分析，論證了採用鋼斜撐方案加固已有鋼吊車梁的合理與有效性。 -
And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency
針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題，本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀；其次對整個吊車梁系統的外觀情況（包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等）進行了現場調查，抽樣實測了梁的應力、化學成分、變形及軌道偏移等，根據實測結果，對吊車梁系統的承載能力進行了驗算；然後，根據現場調查及計算結果，探討了焊接鋼吊車樑上部區域疲勞破壞的機理，分析了重級工作制鋼吊車梁出現疲勞裂縫的原因，制定了初軋廠精整車間破損鋼吊車梁的加固方案；最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。 -
Transfer crane system
搬運吊車方式 -
Yard crane system
場地起重機裝卸方式 -
Auto - loading measuring control system for liquid production in train loading crane system
定量自動裝車技術在液態類物料鶴管裝車系統中的應用 -
Its mechanism is expatiated and its work principle is explained with the crane system
通過對系統原理及平衡閥的結構分析，開發設計了帶旁通油路的平衡閥。 -
A new method is necessary. in this paper, we employed the i - deas software to developed a 3 - d model and make a finite element analysis ( fea ) on slewing frames based on the nominal loads and geometry parameter of crane qtz63, aimed to find the principle of the area with high stress and big deformation and estimated the effect on the whole tower crane system
本文以qtz63塔機為研究對象，按設計提供的載荷及幾何參數，運用i - deas軟體先對回轉支承系統三維建模，再進行結構有限元分析，依據強度及變形結果，找出塔機各種工況下高應力區域、變形明顯部位出現的規律，並分析對塔機系統產生的影響。
分享友人