crest factor 中文意思是什麼
crest factor
解釋
波峰因數-
Furthermore, this dissertation also gives a comprehensive analysis and comparison to the torque ripple factor, torque - current ratio and other aspects for pseudo - sinusoidal emf bldcm drived by 120 conduction mode, 180 conduction mode and self - synchronous svpwm mode respectively. the simulation and the experimental results indicate that self - synchronous svpwm method is more effective for minimizing the torque ripple without any expense of the torque - current ratio when the crest width of the back - emf waveform is less than 107 electrical angles
對準正弦波反電動勢無刷直流電動機在120導通方式、 180導通方式和自同步svpwm三種控制方式下的轉矩脈動系數、轉矩電流比等方面進行了全面的分析與比較，模擬研究和實驗結果表明，當反電動勢的平頂寬度小於107電角時，採用自同步svpwm控制方法可以在不損失轉矩電流比的基礎上，更有效地抑制電磁轉矩脈動。 -
We discussed the main characteristic parameters of seismic kinesiology and dynamics of mine engineering fracture zone, including relative amplitude, phase time of wave crest, similarity factor, principal frequency band energy, 3 - d space time gradient and coherent coefficient et al., and puts forward the processing method of 3 - d seismic characteristic parameters about denoise - smoothing, generalization, correlation analysis, characteristic transformation ; and presents the method of pattern recognition of mine engineering fracture zone
摘要本文從時間域、頻率域、三維空間域介紹了礦山工程裂隙破碎帶主要的地震運動學、動力學屬性參數，包括相對振幅、波峰相位時間、相似系數、主頻帶能量、二維空間時間梯度和相干系數等，提出了礦山工程裂隙破碎帶三維地震屬性的去噪平滑、歸一化、相關分析、特徵變換的處理方法以及裂隙破碎帶的模式識別原理與方法，並用實例說明了該方法的應用效果。 -
For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率 -
The results of the experiment show that the peak value, rms, standard deviation, crest factor, kurtosis value and impulse value of the vibration signals can distinguish between the normal and abnormal conditions of the ball bearing when the level of noise is low
常用包絡解調技術對此類信號進行分析，但易受噪聲影響，使得齒輪或滾動軸承的故障特徵難以凸顯。本文從研究相關函數的特性入手，經理論證明，發現自相關函數並不改變調制信號的調制特徵，但具有顯著的降噪特點。
分享友人