cross section imaging 中文意思是什麼

cross section imaging 解釋
切面顯象
  • cross : n 1 十字架；〈the C 〉 耶穌受刑的十字架。2 〈the C 〉 基督教（教義，國家）。3 不幸，苦難；挫折，...
  • section : n 1 （外科、解剖的）切斷；切割；切開。2 【外科】切片，【金相】磨石。3 （果子的）瓣。4 【數學】截...
  • imaging : 成像
  1. Second, the imaging model built here has taken into account the tilt modulation, the hydrodynamic modulation, and current modulations of radar cross section. consequently, it has realized the imaging simulation of four kinds of wakes with the same imaging model. third, the orbital velocity of ocean wave was considered as the basic dynamic factor, and the imaging model calculates the influence on raw data by the wave m ovement according to the orbital velocity

    該模型的主要特點是： （ 1 ）它採用了三尺度復合表面模型的思想來計算海面的電磁散射，考慮了中等尺度波對紋波的進一步調製作用，彌補了傳統雙尺度模型的不足； （ 1 ）它考慮了海浪的傾斜調製作用、流體動力調製作用和流場對雷達截面的調製作用，實現了用統一的模擬模型對四種艦船尾跡特徵進行成像模擬； （ 3 ）它把海面長波的軌道速度作為基本的動態成分，並依此來考慮海面運動對sar回波信號的影響。
  2. The dissertation is mainly including four section : the first is the experiments done in the tank, which will supply the reliable information of imaging data ; the second is image edge detection by the use of the art of the zernkie moments, which is used to detect the liner and threaded edge of the object, the third is the underwater camera calibration technique, the forth is automatic positioning the location of the camera by used of the art of cross - ratio, the result of which is satisfied

    本文工作分為四個部分：第一部分是水槽實驗部分，它為后續的工作提供了可靠的圖像數據信息；第二部分是基於zom距的直線、曲線邊緣提取技術及相關的與處理技術；第三部分，水下攝像機標定技術研究，基於改進的tsai演算法，採用逐步分解的標定策略。並探討了一種相對簡單的、靈活的標定技術；第四部分是攝像機定位技術研究，採用具有平移不變性的交比進行攝像機定位，模擬試驗的最大誤差不超過2 ，效果還是令人滿意的。
  3. The software of analysis method of multi - armed caliper log imaging has been developed, and the on - site applied results show that the software can get the casing maximum drift diameter and effective drift diameter and simultaneously give the caliper hoop extension graph and cross section graph in arbitrary depth which can diagnose the sort and degree of casing deformation

    摘要研製了多臂井徑成像測井解釋方法軟體，現場應用結果表明：運行該軟體可以解釋得到套管最大通徑、有效通徑；同時給出任意深度井徑周向展開圖、橫截面圖，進而可判斷套變的種類和程度。
  4. Cross - section imaging measurement simultaneously digitizes both exterior and interior surfaces of a part, a full data geometry model of a part can be constructed. the technique helps to shorten the design - to - manufacture time and reduce the cost of the product

    採用層去圖象法測量技術可以同時測量零件的內外輪廓特徵，得到零件的完整數據模型，精度也較高，而且還有助於縮短產品的設計和生產周期，降低生產成本。
分享友人
分享到 Line

分享到臉書