crosstalk coupling 中文意思是什麼
crosstalk coupling
解釋
串音耦合、串話耦合-
Traditional static crosstalk identification methods identify crosstalk targets only using coupling capacitance and noise amplitude information, which lead to the pessimistic results and induce a long time to ic design convergence
摘要傳統的靜態串擾噪聲識別演算法只驗證耦合電容和噪聲幅值信息，沒有考慮噪聲寬度對電路邏輯功能的影響，所以給出的結果過于保守，導致設計收斂的時間被延長。 -
Not only fault model, but also test arithmetic demand to be farther improved. the thesis, focusing on the 20 - port register file, makes a fault analysis, particularly in complex bridge fault and crosstalk coupling fault aroused by word - line and bit - line of 20 - port
本文針對所設計的寄存器文件進行了故障分析，特別對20埠字線、位線引起的復雜橋接故障和串擾導致的耦合故障進行了詳盡論述。 -
An algorithm to resolve the coupling effect problem is proposed during the cross point assignment ( cpa ) stage. in the algorithm, the priority queue concept and the rip - up and reroute strategy are combined to control crosstalk noise caused by interconnect coupling capacitance. first, the nets are arranged into different priority queues according to their weighted sum of their length and criticality. then, the cpa problem for one queue of nets is translated into a linear assignment problem. after the assignment of one queue of nets, a post - cpa checking routine is performed to check and rip up the net pairs which violate the crosstalk noise constraint and then push them into the next queue to be reassigned. the algorithm is tested by a set of bench mark examples, and the experimental results are promising
提出了一種在過點分配階段解決噪聲耦合效應問題的演算法.該演算法採用優先隊列同拆線重布策略相結合的方法，控制由互連線耦合電容引起的串擾噪聲.演算法中，首先按照線長和約束限制，將線網劃分到若干個優先隊列中.然後，將每個優先隊列的過點分配問題轉換為線性分配問題.在完成一個線網隊列的分配后，通過過點分配后處理過程檢查串擾約束滿足情況，對違反約束的線網對進行拆除，放入后續線網隊列進行重新分配.實驗數據表明，該演算法能夠取得好的效果 -
Abstract : an algorithm to resolve the coupling effect problem is proposed during the cross point assignment ( cpa ) stage. in the algorithm, the priority queue concept and the rip - up and reroute strategy are combined to control crosstalk noise caused by interconnect coupling capacitance. first, the nets are arranged into different priority queues according to their weighted sum of their length and criticality. then, the cpa problem for one queue of nets is translated into a linear assignment problem. after the assignment of one queue of nets, a post - cpa checking routine is performed to check and rip up the net pairs which violate the crosstalk noise constraint and then push them into the next queue to be reassigned. the algorithm is tested by a set of bench mark examples, and the experimental results are promising
文摘:提出了一種在過點分配階段解決噪聲耦合效應問題的演算法.該演算法採用優先隊列同拆線重布策略相結合的方法，控制由互連線耦合電容引起的串擾噪聲.演算法中，首先按照線長和約束限制，將線網劃分到若干個優先隊列中.然後，將每個優先隊列的過點分配問題轉換為線性分配問題.在完成一個線網隊列的分配后，通過過點分配后處理過程檢查串擾約束滿足情況，對違反約束的線網對進行拆除，放入后續線網隊列進行重新分配.實驗數據表明，該演算法能夠取得好的效果 -
Crosstalk coupling loss
串音耦合損耗 -
In the course of our static crosstalk noise identification, the noise width along with coupling capacitance and noise amplitude are used to identify static crosstalk noise targets, which overcomes the conservative defect of previous methods
文章在傳統演算法的基礎上增加了噪聲寬度這一識別指標，克服了以往演算法結果過于保守的缺點。 -
To the pcb, here detailedly introduce all kinds of disturb, sensitive element and the coupling modes of transmit. here mainly analyse the master coupling route ( the trace of the pcb ) and the shield of crust in theory, set up the models of them include the study on the effect of an external electromagnetic interference on a pcb trace, the study on the effect of an hole leak electromagnetic interference on a pcb trace and the study on the crosstalk analysis between two transmission - lines of pcb
詳細介紹了pcb上的電磁兼容原理，對于主要耦合干擾途徑（對pcb上走線的耦合）和pcb的外殼屏蔽進行了詳細的理論分析及推導，對pcb板上微帶線走線的各種耦合情況和外殼屏蔽進行了建模，包括外電磁場對走線的耦合、孔縫泄漏場對走線的耦合、走線之間的串擾等情況。
分享友人