crystallization morphology 中文意思是什麼

crystallization morphology 解釋
結晶形態學
  • crystallization : n. 晶化，結晶（作用，過程）；結晶體；具體化，明朗化。
  • morphology : n. 【生、地】形態學；【語法】詞法；詞態學；【生物學】組織,形態。n. -gist 形態學家。
  1. The properties of thin films have been investigated with modern analysis technique, such as afm ( atom force microscopy ), sem ( scanning electron microscope ), xrd ( x - ray diffraction ) and rocking curve ( - scan ). and the properties of ybco thin film and its substrate and deposition temperature have been analysed, comparing with lao substrate ' s crystallization quality, ybco thin film properties, such as morphology and degree of grain alignment, was concluded to correlate with the crystal orientation uniform of lao substrate as revealed by xrd

    本文結合afm 、 sem研究ybco薄膜的表面形貌， xrd 、 fwhm分析薄膜的結晶情況，並結合成膜溫度和基片的質量進行一系列結構與性能的對比研究，發現laalo3 （ lao ）基片的質量對ybco薄膜的結構完整性有很大影響，不僅影響了薄膜的c軸取向性，而且影響了ybco的超導性能。
  2. In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed

    本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。
  3. Isothermal and non - isothermal crystallization behaviors were also investigated. the results of ft - ir, uv spectrum, waxd and sem indicated that rigid rod polymer polyazomethines were polymerized in the composites. the addition of pam changed the crystallization morphology and apparent crystallinity of the composites, but did not change the basal crystal form

    通過對復合材料ft - ir 、紫外光譜、 waxd和sem等測試分析，表明復合材料中存在剛性棒高分子聚甲亞胺，其存在改變了pa - 6的結晶形態和表觀結晶度，但尼龍6的晶型並沒改變。
  4. Studies on the morphology and crystallization behavior of ptt pet blend systems

    共混體系晶體形態與結晶性能的研究
  5. Two coating approaches were adopted, one was to do next coating after 550 ? heat - treatment ( called a coating technique ) ; the other was to do next coating after 100 ? drying, the films coated by several times were heated at 550 ? ( calied b coating technique ). xrd, sem, tem and afm were used to characterize the crystallization behavior, orientation and surface morphology of the zno thin films

    運用xrd 、 sem 、 tem以及afm等對所得的樣品進行了分析和研究，結果表明：採用不同的旋塗工藝得到不同的薄膜厚度，而採用每次塗膜形成氧化物膜后再進下一次塗膜的方式能更好的保持zno薄膜的c軸擇優取向生長。
  6. By compounding caco3 with pp, the effect of caco3 content, diameter and shape on the crystallization, dispersion morphology and properties of pp / caco3 composites was investigated. the results showed that addition of caco3 into pp decreased the apparent crystal size in perpendicular direction to the ( 110 ), ( 040 ) and ( 130 ) crystallographic planes of ppa crystal, and with similar uniform dispersion of caco3, the dominant factor influencing toughness is the diameter of caco3 particles, but not the decrease of pp crystal size. the toughening effectiveness of nano caco3 is obviously better than that of micron caco3

    將caco _ 3與pp進行填充復合，研究了caco _ 3含量、粒徑及形狀對體系的結晶，分散形態及性能的影響，發現碳酸鈣的加入使聚丙烯晶型垂直於（ 110 ） 、 （ 040 ）和（ 130 ）晶面的表觀晶體尺寸減小，揭示了在分散均勻的情況下，影響材料韌性的主導因素不是晶粒尺寸的減小，而是碳酸鈣的粒徑，納米張玲：彈性體及無機剛性粒子增韌增強聚丙烯復合材料的研究碳酸鈣的增韌效果明顯優于微米碳酸鈣。
  7. In this work, zno thin films were prepared by sol - gel method on the glass substrate in order to study the influence of the preparation techniques on the crystallization, orientation and morphology of the films. we adopted a two - step heat treatment technique to optimize the micrcjstructure of the films, and subsequently discussed the forming process of the zno thin films

    本論文研究了在載波片和si （ 001 ）上溶膠凝膠旋塗法的制備工藝對薄膜的結晶、取向狀況以及薄膜形貌的影響，探討了溶膠凝膠旋塗法制備的氧化鋅薄膜的形成過程，同時引入兩步熱處理方法來優化薄膜的結構。
  8. Keywords : reactive - crystallization, calcium oxalate hydrates, induction time, nucleation, morphology

    關鍵詞：反應結晶、含水草酸鈣、感應時間、成核、晶型。
  9. Zno thin film had a better crystallization with increase the substrate temperature. the buffer layer thickness effected crystalline quality and morphology of zno thin film. the results showed that the film had the best crystalline qulity and morphology when the buffer later thickness was 36nm

    緩沖層的厚度對薄膜的結晶質量和表面形貌有很大的影響，研究發現，緩沖層厚度36nm時， zno薄膜有最優的取向和最平滑的表面。
分享友人
分享到 Line

分享到臉書