curing speed 中文意思是什麼

curing speed 解釋
固化速度
  • curing : （質粒）清除[從宿主細胞中除去質粒
  • speed : n 1 快，迅速。2 速率，速度。3 （汽車的）變速器，排擋。4 （膠片，照相紙）感光速度。5 〈古語〉興隆...
  1. The resin produced by the flame - retardant products with high strength and mechanical properties, thermal deformation temperature, curing speed, and good soak

    該樹脂所生產製品具有很高的阻燃性能和機械強度，熱變形溫度高，固化速度快，浸透性好。
  2. Xt - p1007 unsaturated polyester resin is reactive flame retardant resin, heat distortion temperature, curing speed, good soak and toughness, both major requirements for flame - retardant and high mechanical strength requirements pultruded products

    P1007不飽和聚酯樹脂是反應型阻燃樹脂，熱變形溫度高，固化速度快，優良的浸透性和韌性，主要應用於既要求阻燃又要求機械強度高的拉擠產品。
  3. Using silicon dioxide, magnesia, aluminum hydroxide to react with sulfonic acids, color fixatives under standard proportioning, through curing and drawing into thread - like form, this product is made with mechanical twisting as per specific speed and number of strands after drying treatment, featruing a certain tensile strength

    本品用二氧化硅、氧化鎂、氫氧化鋁同磺酸、固色劑等按標準配比反應，經固化抽制線狀，再經乾燥處理后，並按規定速數和股數，經機械加捻而成，並有一定的抗拉強度。
  4. The preparations, drilling rig adjustment, pile distribution control, mixing verticality control, elevation measurement, elevation control of pile top and column bottom, curing agent choice and control of mixing speed and blending quantity, must be done well for strengthening soft soil foundation by mixing cement with soil in construction

    在實踐中要做到6點： 1 ）調整好鉆機； 2 ）控制好柱的分佈位里與攪拌軸的垂直度； 3 ）測量好高程； 4 ）控制好樁頂、柱底高程； 5 ）選擇好固化劑； 6 ）控制好攪拌速度和摻加量。
  5. Reconstruction research on high speed paper receiving system of kdf - 2 tobacco - curing machine

    2卷煙機高速接紙系統改造與實驗研究
  6. Results showed that temperatures have different effects on the curing speed of resin, the rate of moisture transmission, the degree of plastic melting and the degree of wheat straw decomposition

    結果表明，熱壓溫度對板坯中膠黏劑的固化速度、水分傳遞速度、塑料熔融程度、麥秸分解程度等都有不同程度的影響。
  7. While the curing speed of intra - gallery was slower than that of extra - gallery, exfoliation never happened

    當蒙脫土層間的固化速度小於層外固化速度時，則不能。
  8. By variation of curing agents of epoxy and modifier of clay, the different curing speed of intra - gallery and extra - gallery could be obtained

    通過調節有機插層劑和固化劑，可以獲得不同的層間和層外的固化速度。
  9. It was found that exfoliation of clay occurred when the curing speed of intra - gallery was faster than that of extra - gallery even the epoxy / clay compositions were cured at any temperatures, for any time and with any types of curing agents

    研究表明，當蒙脫土層間的固化速度大於層外固化速度時，採用不同的固化劑，固化不同時間，在不同的溫度下固化都可以得到剝離型的環氧/蒙脫土納米復合材料。
分享友人
分享到 Line

分享到臉書