current induction method 中文意思是什麼

current induction method 解釋
電流感應法
  • current : adj. 1. 通用的，流行的。2. 現在的，現時的，當時的。3. 流暢的；草寫的。n. 1. 水流；氣流；電流。2. 思潮，潮流；趨勢，傾向。3. 進行，過程。
  • induction : n 1 引入，誘發，誘導（作用）。2 【邏輯學】歸納法，歸納推理 （opp deduction）。3 就職，就職典禮；...
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously

    應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。
  2. Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method

    在本設計中，採用高速的dsp處理器，實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法，實現了大電流信號的驅動輸出;採用485總線技術，組建了裝置主機與多探測器之間的主從式通訊網路，實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路，採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術，實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元，設計了人機信息交互的介面;採用了模塊化的軟體設計方法，開發了裝置主機及探測器的軟體程序。
  3. Current induction method

    電流感應法
  4. The paper establishes mathematics model of electromagnetic heating system of eddy current field and temperature field, and gives corresponding discrete format with elements as eight nodes, hexahedron equal cell, through calculating eddy - current field to gain the internal heat source that the temperature field needed, to use discrete method to solve the problem of induction - heating part ' s temperature field by axial symmetrical electromagnetic, and then to analyze the characteristic of instantaneous temperature field

    本文建立了電磁加熱系統的渦流場和溫度場間接耦合的數學模型，分析了不同頻率下渦流和溫度的分佈情況，並以八節點六面體等參元為例給出了渦流場對應的離散格式，通過計算渦流場獲得溫度場所需要的內熱源強度，加熱部件的溫度場以軸對稱格式進行離散求解，並對瞬態溫度場有限單元法的求解特點進行了分析。
  5. The paper lucubrated the control theory of induction motor ' s vector transform and the method of calculating speed by induction motor ' s torque current weight, based on which, the paper designed a close - loop speed - sensorless vector control vwf system and realized the system in matlab / simulink

    本文深入研究了感應電動機矢量變換的控制理論和利用電動機轉矩電流分量進行速度推算的方法。在此基礎上設計了一個閉環的無速度傳感器矢量控制變頻調速系統。
  6. In this paper, a new method is proposed, using the instant response of the induction motor to voltage pulse and current break when the motor stops

    本文首先利用感應電動機對脈沖電壓和階躍電流的瞬態響應，對電機參數進行了靜態測量，模擬結果表明了方法的可行性。
  7. We design inversion control circuit with cmos figure pll cd4046 act as core and microprocessor 80c196kc act as assistant controller. adopting a control method that combine fuzzy controller and pll control, improve induction heating power succeed in startup. adopting electric current voltage pair closed loop feedback design, with trough route capacitance voltage and trough route electric current act as pair closed loop feedback signal, guarantee induction heating power output accuracy

    並對系統主電路的元器件參數進行了詳細的計算；設計了以cmos數字鎖相環cd4046為核心、以80c196kc作為輔助控制器的逆變控制電路；採用了模糊邏輯與鎖相環相結合的控制技術，提高了電源的啟動成功率；採用電流、電壓雙閉環反饋方案，採用槽路電容電壓和槽路電流作為反饋信號，從而保證了電源功率的輸出精度。
  8. Firstly, the experimental phase current and input power data obtained from load test are employed to estimate the parameters in ii rated condition. then, the phase current and input power data in locked rotor condition are used to track the variation of the parameters of the secondary coil with slip frequency. the classical method and the direct modification method are also used to estimate the parameters of the induction machine in comparison with this technique

    首先利用了負載試驗的定子電流和輸入功率數據來識別額定工況下的電機參數，然後又使用了堵轉時的定子電流、輸入功率數據來識別電機二次繞組參數隨轉差頻率的變化，並與傳統參數測試方法和直接修正參數法進行了比較。
  9. Chapter 2 compares the differences of the current - fed converter and the voltage - fed converter used in induction heating power, then induces the power regulation methods of the series resonant inverter and compares the characteristic of these methods. and then, a capacitive pwm & pfm control method which is suitable for medium and small power out induction heating is given

    第二章對感應加熱電源中的電流型逆變器和電壓型逆變器作了比較分析，歸納了串聯諧振逆變器幾種常用的調功方法，對這幾種控制方法的優缺點進行了比較，提出了適用於中小功率感應加熱的容性pwm & pfm控制方法。
  10. In addition the h. kantz method is applied to analyze the time series of the motor current, the maximal lyapunov exponent calculation is realized, the criterion for the motor chaos is brought forward, the existence of chaotic phenomenon in the induction motor is verified by the characteristic exponents, which proves theoretically that the chaotic movement is one of the reasons that results in the low frequency oscillation of the induction motor system

    應用h . kantz方法對電機電流信號的時間序列分析，實現了最大李亞普諾夫指數的具體演算法，提出了電機出現混沌運動的判定根據，通過特徵指數驗證了異步電動機現象的存在，從理論上說明混沌運動是異步電動機系統產生低頻振蕩的原因之一。第三部分深入研究了系統低頻振蕩的主要影響因素。
  11. The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented

    採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。
分享友人
分享到 Line

分享到臉書