curve of error 中文意思是什麼
curve of error
解釋
誤差曲線-
Based on the curve, the adulterated peanut oil can be detected fast, the error amount of which is at least 5 %
發現油中脂肪酸組成及其特徵組分的變化成線性規律，由此做出工作曲線，可快速定性、定量摻偽油，且摻偽量的最低檢出限可達到5 % 。 -
The relation of radius of curvature and error as well as formulas of increasing parameters on condition of constant error are diverted. the equation of the line on the center of approximate circular arc is obtained ， and it can avoids the trouble that numerical solution owns possibility of no convergence and simplifies node calculation of non - circular curve
導出了曲率半徑與逼近誤差之間的關系和等誤差條件下的參數遞推公式，建立了通過逼近圓弧圓心的直線方程和圓心坐標計算公式.按這種方法用圓弧逼近平面參數曲線，不需要求解非線性方程組，避免了計算可能不收斂的麻煩，簡化了非圓曲線的節點計算過程 -
Method of deal with data error by subsection curve fitting and discrete degree
分段曲線擬合與離散度加權的數據誤差處理方法 -
During the instantaneous frequency estimation of lfm, there exists some error in the edge, so in the dissertation, a fitting method is proposed to modify it. from the computer simulation, the following result is obtained : for cw, the method based on cwt is most effective, and with the snr rising, the error curve of it is more and more closer to crb. for lfm, the method based on wvd gives the best result, and the effects of cwt and stft are similar for multi - component signal, compared to stft and wvd, cwt is a better choice
通過模擬發現，在單頻回波的瞬時頻率估計中，基於cwt的方法最為有效，隨著信噪比的提高，其均方誤差曲線越來越接近克拉美?羅界；在線性調頻回波的瞬時頻率估計中， wvd法得到的效果最好，而cwt與stft法的估計效果比較接近；在多分量信號的瞬時頻率估計中，相對于stft和wvd法， cwt法是一個更好的選擇。 -
Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve
建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。 -
With the experiment part, the errors of sk - 21 nc machine tool have been measured, and a serial of data is gotten which lead to the error discrimination. ( 3 ) based on the kinematical theory of mbs, the calculation methods for the ideal center envelop curve of grinding wheel on cam grinding, the practical cutter track, inverse contour of cam, ideal nc instructions, precision nc instructions, the inner / outer normal and the fitting criterion of curve have been all discussed in detail in this paper
（ 3 ）通過精密加工的約束條件方程，探討理想刀具路線、逆變數控指令與實際刀具軌跡之間的映射關系，解決誤差補償技術提高加工精度的核心問題? ?當要求數控磨床的砂輪中心準確到達給定的理想點時，精密數控指令值究竟該是多少，如何能夠通過計算，獲得這樣的數控指令值，給出經修正的數控指令計算方法。 -
Aiming at the study actuality of fan performance monitoring system and analysis of fan performance curve changes affected by inlet - box and the different fixed - angles of guide blades in the course of installation, a fan flow monitoring model based on rbfnn in whole flow zone was established in this thesis. in the model, the method of no throttle and fan performance curve were used as basis. and on the basis of that model, fan performance curves of 4 - 73no. 8d were approached with experimental data of different speed, different opening - angles of guide blade and different resistance of pipeline, the precision and the error law of model were studied
本文針對電站風機性能監測系統研究較少的現狀，在實驗的基礎上分析了現場加裝進氣箱和由於安裝造成的導流器葉片開度不一致對風機性能曲線的影響，並在此基礎上採用無節流方法測量流量，以風機調節性能曲線為依據，建立了基於徑向基函數（ rbf ）神經網路的風機流量全程監測模型；以實驗室4 - 73no . 8d離心風機為研究對象，探討了rbf神經網路差壓模型在變轉速、變導流器開度和變管網阻力等工況下的應用精度和誤差分佈規律；最後用visualc + +語言開發了風機性能在線監測系統。 -
The existed material fatigue performance test curves are dealt with and analyzed, and the non - dimensional stress - strain curve, tangent modulus factor curve and fatigue life curve are drawn based on the experiment data, and these three non - dimensional parameter curves are used to find the inherent rules that the test curves can be replaced each other to some extent. it can be concluded that if the common character and system error of these materials are found, the test curve of a certain material can be used for reference by another material. this is a simple approach about fatigue life estimate and is engineering practical
對已有的材料力學疲勞性能試驗曲線進行分析整理，利用試驗數據繪制了相對應力應變曲線、切線模量因子曲線和疲勞壽命曲線，利用這三種無量綱參數曲線發現了其中存在的規律性，即在某種程度上實驗曲線可以互相取代，並用試驗數據對此進行了討論，並由此推斷，如果找出材料彼此的共性或彼此之間的系統誤差就可以將一種材料的試驗曲線供其它材料參考使用，這是一種估算材料的疲勞壽命的簡便方法，對工程而言具有實用性。 -
But, the measured - data is a very great quantity and every data contain all data of 1 - 25 harmonic, measured time can have hours to days. the count by hand is very heavy and over - elaborate, sometimes the statistics results is error. it won " t reach the analysis purpose and don " t obtain the curve of harmonic oscillation characteristic in a row frequency range
可是，測試數據經常是大量的，每一組數據又包含從基波到25次諧波的所有數據，測試時間可能是幾個小時，有的甚至是幾天時間，這樣的工作量由人工完成是非常繁重的，又是非常繁瑣的，有時還統計不出正確的數值，起不到應有的測試分析目的，更無法獲得連續頻域內的諧波諧振特性曲線。 -
Data processing is performed by pc ， which includes detecting rough error by quartile method base on first order differential, adopting three points algorithm to eliminate deviations of rack displacement and installation, applying minimum containing area method to evaluate the sectional plane radius of roller and realizing it by genetic algorithm, adopting akima method to fit curve of roll profile
主要的數據處理工作在上位機進行，採用基於差分法的分位數演算法剔除粗大誤差；採用三點式測量原理消除探頭的安裝及運動所產生的誤差；採用最小包容區域法評定軋輥半徑，並應用遺傳演算法實現最小包容區域法的尋優計算；採用阿克瑪插值方法進行輥型的曲線擬合。 -
With metal fatigue in material mechanics, this paper deduces the limestone fatigue curve of longmen grottoes by means of marble s one within the error permission. by the experiment elects the crucial factors of current vibration environment in longmen grottoes, the author contrasts the result of the experiment with its fatigue curve referred above and analyses the fatigue effect of longmen grottoes. finally, it is pointed out that after longmen grottoes have being suffered weathering and water - erosion more than 1500 years, the vibration environment is becoming an crucial factor leads to fatigue effect, especially in those weak surface carvings just like the crossings of several rifts, serious weathering places, etc
借鑒材料力學中金屬疲勞破壞的研究手段，在誤差允許范圍內用大理巖疲勞曲線推導出門石窟石灰巖疲勞曲線。通過對石窟實際振動環境中典型要素的抽取和振動試驗，將試驗結果與疲勞曲線進行對比，分析了門石窟的疲勞破壞效應。文章指出，在經歷了1500多年的風化和流水溶蝕后，振動環境已成為導致門石窟某些薄弱點如多條裂隙交叉點嚴重風化酥解的壁面雕刻品等產生疲勞破壞的重要誘發因素。 -
According to the principle of curve axial symmetry, authors inferred the theoretical foundation of error - free translation of the working equipment of loader and proved that when the diameter of piston rod on arm oil cylinder was designed properly, the two oil cylinders could be guaranteed to have a synchronous movement which made the bucket maintain translation throughout the working process under the condition of the oil cylinder ' s basic parameter ; also made the equipment structure of the loader greatly simplified and provided the reference for improvement of the present equipment of loader
根據曲線軸對稱原理，推導出了能使裝載機工作裝置無誤差平移的理論基礎，證明了只要適當地設計動臂油缸活塞桿直徑，就可以在油缸的基本參數上保證機構工作時兩油缸同步運動，使鏟斗在作業過程中保持平移；使裝載機工作裝置結構大為簡化，為進一步改進現有裝載機工作裝置提供參考。 -
For compensating the nonlinear error between winding current and the result magnetic field of stepper motor, the method of minimum square is adopted to fit and correct the error curve of subdivision step angle, and the subdivision precision is improved
為了補償步進電機相繞組電流與其產生磁場之間非線性引起的誤差，採用了最小二乘法對細分步距角誤差曲線進行了擬合與修正，提高了細分精度。 -
Data processing method of coordinate measurement for complicated curve profile error
的白車身三坐標測量數據處理分析系統 -
The apsp produced abroad is made by numerical controlled machine tool, which has noise level of 71db ( a ), the apsp produced in our country is made in the method of exploratory which has noise level of 73db ( a ) and 75db ( a ). in order to analyze the influence of stator curve to noise, the author used tri - coordinate measuring instrument to measured exactly the inside surface of stator and got the straddling point coordinate, and made curve fitting by using matlab as language and studied the fitting effect and then worked out the equation of stator transition curve in return seeking, then comparied this method with the standard style and made the conclusion : the equation of atator transiting curve of apsp made by numerical controlled machine tool is close to theorical 5 power curve standard style, but compared with it, the stator transiting curve of apsp produced in exploratory has a major error. combining the testing results of noise, one can know that the qualily of stator transition curve play an importance to t he noise of the pump
國外生產的汽車動力轉向泵是用數控機床加工的，其噪聲值為71db （ a ） ，國內生產的汽車動力轉向泵是用靠模方法加工的，其噪聲值分別為73db （ a ）和75db （ a ） ，為了分析定子曲線對泵的噪聲的影響，本人用三坐標測量儀對定子內表面進行精密測量，獲得定子內表面的離散點坐標，以matlab語言為工具對離散點進行曲線擬合，觀察擬合效果，然後，用回歸方法求出了定子過渡曲線的方程，並把該方程與理論方程標準型進行了比較，得出如下結論：用數控機床生產的汽車動力轉向泵的定子過渡曲線方程非常接近理論5次曲線標準型，而用靠模方法加工的汽車動力轉向泵的定子過渡曲線與理論5次曲線標準型相比較，則存在著較大的誤差，結合噪聲測試結果可知，定子過渡曲線的優劣，對泵的噪聲大小有著重要的影響。 -
The secant modulus is used to calculate final settlement of high - stacked soil, compared with the result of e ~ p curve, the error is in the limit of tolerance
同時將割線模量計算沉降的方法應用到高填方自身作用下的最終沉降計算中，通過與應用e p曲線計算的結果進行比較，其誤差在允許范圍之內。 -
Designing curve is obtained by iteration, and the least time is achieved based on the requirement of error
通過迭代確定了設計曲線，並且根據誤差要求確定了最小迭代次數。 -
The main contents are as follows : 1 ) 3 eliminate error criterion method and step wise regression analysis method is used to analyze the errors of observation date. in the stepwise regression analysis, aging, loading and temperature which bulkily affects the dam ' s vertical deformation are selected as the regression factors, then regression equation and curve of each point are worked out
運用3準則剔除誤差法和逐步回歸分析法對茅坪壩的觀測資料進行誤差分析，在逐步回歸分析中，選用對壩體豎向變形影響較大的時效、施工加載和溫度作為回歸因子，求出各測點的回歸方程和擬合曲線。 -
Taking no account of the non - uniformity of the detector, this paper analyzed the performance of the traditional four - quadrant angle - measurement algorithm and two other algorithms in calculating the pitch angle and the deflection angle of the incident ray, and also compared the error curve of the pitch angle calculated by each algorithm in the full plane
摘要在不考慮探測器非均勻性影響的情況下，本文分析了傳統四象限測角演算法和另外幾種演算法在計算入射光的俯仰角和偏轉角時的性能，還比較了在整個平面內各個演算法得到的俯仰角的誤差曲面。 -
This paper focuses on the research of fuzzy control, especially rule self - adjusting fuzzy control method. by theoretic analysis and simulations, the influences of parameters and system performance characteristic of some kinds of rule on - line self - regulating fuzzy control methods are discussed, and a novel real - time self - adjusting fuzzy control method ( vsrsafc ) is proposed from the diagrammatic point of view. in vsrsafc, the slope of the rectifying curve of rule scaling factor a is altered by the fine - tuning and coarse tuning combined mechanism to adjust the fuzzy control rules according to error e and error change ec, which more coincides with characteristic of system response than the conventional self - adjusting method that adjusts rule scaling factor only according to the error e, and has better static and dynamic performances than the latter
其中變斜率規則自調整模糊控制的效果較為明顯，它是基於插值的非線性規則自調整模糊控制的引申以及常規全論域規則自調整模糊控制的改進，該方法採用粗、細調結合機制，通過改變規則調整因子的修正曲線斜率，使系統同時根據誤差e以及誤差變化ec在線調整模糊控制規則，比傳統的僅基於系統誤差e的自調整方法更符合系統響應特性，可獲得更好的動靜態控制性能，特別是對于系統參數發生改變、控制參數選取不當等不良狀況，控制器仍能較快自調整，具有較強的在線自適應能力。
分享友人