deforming stress 中文意思是什麼
deforming stress
解釋
變形性應力-
The ansys, a kind of fea program, was used to build model of small carriage. the procedure of gantry beam bump with secondary beam of bridge was reappeared by running nonlinear calculation and loading program which was written by apdl program language. the closest deforming result was gotten, and the deforming of main beam, secondary beam and end beam and inner stress distribution status were calculated
採用大型三維有限元軟體ansys對該起重機以及小車架等進行了建模、應用apdl語言編寫加載程序、進行非線性計算，再現龍門橫梁與起重機副梁碰撞過程，最後得到與實際變形結果最接近的一種狀態，得出起重機橋架主梁、副梁、端梁的變形以及其內部的應力分佈情況。 -
During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied
在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。 -
The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed
再現分析得出的主要結論為：橋架的主樑上蓋板主焊縫的最大應力超過了許用應力，但小於屈服極限，可以繼續投入使用；副梁內部的應力遠遠超過了強度極限，變形特別嚴重，不能滿足生產要求，因此更換新的副梁；端梁內部的應力超過了屈服極限，小於強度極限，在應力較大的位置焊接補強板；投入使用后，要對整個橋架進行定期檢查。 -
The static loading test for three group of testing piles of jiading power plant secend stage project are analyzed and studied in this thesis, and the practical applying of high - accurate data collector, technique of waterproof insulation and testing technique of burying in the body of pile are introduced also. the vertical and horizontal loading features of three group of piles of different kind and constructing technique in different earth layer at the pile point are analyzed and compared and summed up with basic integro - differential equation calculating the pile earth system load transmit, transforming principle of stress - deforming and pile body rating of burying electric measuring element. changing law of stress, and changing law of pile body shifting and bending for different testing piles under vertical and horizontal load are showed so that the loading features of soil layer and pile at testing spot, reliable design data for pile type and base for scientific construction technique are provided
本文僅就嘉定電廠二期工程中的三根試驗樁的靜載試驗進行了分析和研究，利用樁土體系荷載傳遞分析計算的基本微分方程及應力-應變轉換原理，結合預埋電測元件的樁身率定，對三組不同種類、不同施工工藝、不同持力層中的樁的豎直、水平承載特性進行了分析、比較和歸納，通過大量、全面的實測數據，經過整理、轉換和推演，揭示了不同試驗樁在豎直、水平荷載作用下的應力變化規律和樁身變位、撓曲變化規律，最終提供試驗場地土層和樁的承載特性，為該工程合理設計樁型提供了可靠的設計參數，為確定科學的施工工藝提供了有力的依據。 -
Based on the fem analysis and load tests in site, some performances of composite foundation are studied. in this research how the length of pile, the rigidity of pile and area replacement ratio of composite foundation affect the stress in the pile, the siding friction transfer law of pile and the deforming characteristics and bearing capacity of the entire foundation is studied
在進行復合地基性狀的研究中，通過建立不同的有限元模型，研究樁長、樁體剛度、面積置換率對均質地基復合地基樁身應力、樁身側摩阻力傳遞規律、變形特性和承載力的影響。 -
It shows that at the stress concentration zone, changes of mfl were relatively weak with slight deformation of the specimens. with the deforming to plastic and further the changing of mfl exhibits more distinct, and when necking emerging a very intensive change takes place. it is indicated that magnetic memory effect is related to the microstructure of the material
經分析認為，磁記憶信號的這種變化與材料內部微觀組織的狀態有關，試件變形很小時，磁彈性效應對試件表面泄漏磁場的變化起主要作用;試件變形較大時，其表面泄漏磁場的變化主要受塑性變形區內位錯聚集產生的微缺陷的影響。 -
Adapt anti - static high strength carbon curtain imported from french in order to avoid stress deforming when cotton screen is in running
採用法國進口的防靜電高強度碳簾、避免棉網運行中應力變形。 -
In different geologic development stage, different geodynamics background and tectonic stress field characteristic led to different baisin types, sedimentary assemblage. basin - mountain coupling forms and produced complex structure deforming. consequently, superimposed basin are characterized by multi - stage basin - formation, multi - stage hydrocarbon generation, multi - stage hydrocarbon accumulation. complex accumulation mode and oil / gas distribution law. tectonic process is key point and decisive in many hydrocarbon accumulation factors of superimposed basin
在不同的地質發展階段，由於不同的地球動力學背景和構造應力場特徵，導致了不同的盆地類型、沉積組合、邊界條件和盆山耦合形式，產生了復雜的構造變形，從而使疊合盆地具有多期成盆、多期成烴、多期成藏以及復雜的油氣成藏模式和油氣分佈規律。 -
Establishing finite element method pattern analyzed stress and deforming of main parts of impeller and improved the structure of impeller from reducing the concentration of stresses and the abundance of intension
摘要通過建立有限元分析模型，對葉輪的主要零部件進行應力、變形分析，據其結果考慮減少應力集中和強度裕量，改進葉輪結構。 -
The thesis analyzes the inner cracking reason for the hot rolled sheet based on texture orientation transformation, simulates the forming process of drawing sheet by the barlat - lian anisotropic yield criteria, and discusses the cracking mechanism in the deforming and stress distribution
本文由該材料的微觀織構取向變化分析造成板開裂的內在原因，根據能夠準確描述塑性各向異性的材料模型，模擬了沖壓板開裂圓件成型過程，由其變形分佈和應力分佈探討開裂機理。
分享友人