delivery of pump 中文意思是什麼

delivery of pump 解釋
泵的排量
  • delivery : n. 1. 引渡，交付；【商業】交貨；【法律】正式讓渡。2. 運送；投遞；傳送。3. 分娩。4. 陳述，講演；口才。5. 【棒球】投球。6. 救助；釋放。
  • of : OF ＝Old French 古法語。
  • pump : PUMP ＝politically upwardly mobile personality 政治新星，政治上有望晉升人士。n （淺口無帶的）輕舞...
  1. Once the water reaches its maximum speed, the valve slams shut and pressure is built up in the pump. this pressure forces open a second valve linked to the delivery pipe. when nullah water falls past the hydraulic ram, its momentum will lift a tenth of the water to a storage tank located near the esther li building photo 2

    泵內有活門，當溪水在流動中受阻，會產生比正常壓力高十倍以上的瞬時水錘壓力，此時，泵內的另一活門會打開，把十分之一的溪水抽往設于李慧珍附近的儲水缸備用（圖二） 。
  2. Complete air piston pump contains pneumatic motor and piston pump, the ratio of piston area of pneumatic motor and plunger ' s sectional area of piston pump is transforming times of pump pressure ; the higher times, the more pressure can deliver higher viscosity fluid, and achieve the delivery aim

    完整的氣動柱塞泵包含有氣動馬達與柱塞泵兩部分，氣動馬達中的活塞面積與柱塞泵活塞的截面積比值，就是泵壓力轉換的倍數；愈高的倍數就能以愈大的壓力輸送愈高黏度的流體，達到輸送的目標。
  3. The site concrete pump is designed for a delivery rate of 87 m3 / h and maximum pumping pressure of 100 bar

    "現澆混凝土泵設計的輸送速度為87立方米/小時，最大泵送壓力為100巴。
  4. The pressure of pressure stabilizing pump will be settled on the basis of its delivery head which is not calculated but determined by the delivery head of main fire pump as the function of it is to stabilize the pressure inside the fire water system

    穩壓泵的壓力設定值決定於穩壓泵揚程，穩壓泵的揚程一般不另行計算，而是採用消防主泵的揚程，其原因在於設置穩壓泵的目的是使消防給水管網的水壓穩定。
  5. The key to the technological transformation is the design of the manual oil pump 、 the delivery pump and the whole transmission box

    技術改造的關鍵是手油泵、輸油泵及傳動箱總成的設計。
  6. A new concept to determine the delivery head of the pump and to set up the pressure of the system is proposed in this paper, based on the precondition to ensure the water head demand of any fire appliance at the most unfavorable point

    從保證最不利處滅火設施水壓要求這一基本前提出發，提出確定穩壓泵揚程和設定壓力的新思路，並按3種情況分別作出說明。
  7. The great point in favour of this construction is that the medium only comes in contact with the inside of the hose and with the delivery valves and not, as with typical diaphragm piston pumps, with the pump cover or the pump head respectively

    這種泵的結構上的另一個顯著的特點是介質僅與軟管隔膜的內側和閥門相接觸，而不是象典型的隔膜活塞泵那樣，介質同泵腔和泵蓋也都分別會有接觸。
  8. The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them

    在油泵出油閥端，採取漸縮管結構措施，利用管路動態效應提高噴油壓力；對于噴油系統參數：噴油壓力、靜態供油提前角和油嘴凸出高度，三個參數進行調整試驗，找到它們的最佳匹配。
  9. Because it was trouble to control the heavy apron type feeder ' s rotate speed, the paper put forward a new method to achieve control the hydraulic motor speed efficiency by control electro motor rotate speed in transducer to control the hydraulic liquid flux of varable delivery pump

    摘要文章針對重型板式給礦機速度控制困難，提出了用變頻器控制電機轉速來控制變量泵液壓油流量，以實現對液壓馬達速度的調節方法。
  10. Delivery valve of diesel fuel injection pump part 1 : technical specifications

    柴油機噴油泵出油閥偶件.第1部分:技術條件
  11. Delivery valve of diesel fuel injection pump part 2 : performance test method

    柴油機噴油泵出油閥偶件.第2部分:性能試驗方法
  12. Technical specification for delivery valve mating parts of fuel injection pump of marine diesel engines

    船用柴油機噴油泵出油閥偶件技術條件
分享友人
分享到 Line

分享到臉書