drop press 中文意思是什麼
drop press
解釋
【機械工程】模鍛壓力機，落錘。-
The theory basis of selecting the equipment is found by calculating the medium frequency induction hrating furnace and onatching equipment in 125mn drop press production line
摘要通過對125mn熱模鍛壓力機生產線中頻感應加熱爐及配套設備的分析計算，找出了選型的理論依據。 -
Steel forgings ; design of drop and press forgings ; machining allowances, drafts, edge radii, fillet radii, base thicknesses, wall thicknesses, rib widths, and rib radii
鋼鍛件.落鍛和壓鍛設計.第2部分:加工余量拔模斜度 -
Steel die forgings - tolerances on dimensions - drop and vertical press forgings
鋼模鍛.公差和尺寸.落錘或垂直壓力鍛造 -
The presented thesis studies the gas discharge of lab6 electrodes, the paper analyses the impacts of gas press and electrodes separation on the ignition voltage and voltage drop, and makes low gas pressure, lower than 10pa, discharge switch tubes, with gas of helium and nitrogen, electrodes gaps of 5mm. the paper studies the tubes ’ discharge performances, and the impacts of discharge process on the electrodes
分析直流工作條件下，以氬氣、氮氣、氦氣為工作氣體時，氣體的壓強、極間距對著火電壓和管壓降的影響，並製作低氣壓（ < 10pa ）下的氣體放電開關管（放電氣體為氮氣和氦氣，極間距為5mm ） ，研究其在直流和脈沖下的放電特性，以及放電過程對電極的影響。 -
Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings ; german version en 10243 - 1 : 1999, corrigenda to din en 10243 - 1 : 2000 - 06 ; german version en 10243 - 1 : 1999 ac : 2005
鋼模鍛件.尺寸公差.第1部分:落錘鍛造件和垂直壓力鍛 -
Exhale, bend your knees, pull your heels toward your pelvis, then drop your knees out to the sides and press the soles of your feet together
呼氣，彎曲你的膝部，將你的腳後跟拉向你的骨盤，使膝關節向身體兩側向下打開，將兩個腳底板握在一起。 -
Press tab until the main drop - down list is selected
按tab直到選定主下拉列表。 -
Press the f1 key on your keyboard to access the drop - down menus
按鍵盤上的f1鍵以使用下拉菜單。 -
Select the profile to use from the drop - down list in the proof setup dialog box or press load to select your custom profile
在安裝軟體校驗下拉菜單中選擇色彩圖表文件或點擊載入以選擇您的自定義色彩圖表文件。 -
Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings
鋼模鍛件.尺寸公差.第1部分:模鍛壓力和垂直壓力鍛造 -
Steel die forgings - tolerances on dimensions - part 1 : drop and vertical press forgings ; german version en 10243 - 1 : 1999
鋼模鍛件.尺寸公差.第1部分:落錘和立式壓力機鍛件 -
In the text applying the theory of two - phase flow ' press - drop and diversion - phase model, having a analysis to the press characterize of the important part namely the bubble pump of the no - pump libr absorption air - condition, and set up the relational mathematical model
本文對無泵溴化鋰吸收式空調器的關鍵部位，氣泡泵的特性按照流體力學兩相流的理論進行了分析研究，並應用兩相流的分相模型，建立了數學模型，並進行了數值模擬計算。
分享友人