dynamic circuit 中文意思是什麼
dynamic circuit
解釋
動態電路-
In the blue print of the analog, author utilize the big dynamic vga to realize the if amplifier and use the audion to carry out the 80db agc, through the improvement of the traditional detect circuit, extend the dynamic range of the detector
在模擬方案中，筆者採用了大動態的vga實現中頻放大;利用三極體檢波實現了80db的agc控制;通過對傳統二極體檢波電路改進，提高了檢波器的動態范圍。 -
This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves
2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。 -
In the next place, by studying the change of the resonant frequency of the whole system, this paper designs the circuit to track the resonant frequency of the system by cd4046 mainly. at the same time, in order to improve the efficiency and get better dynamic capability of the converter, we choose pll and fuzzy control after comparing the pll circuit, fuzzy circuit and pll ? fuzzy control circuit. in the end, this paper brings forward the control blue print to realize the drive control circuit of the high frequency converter, using the dsp chip as the key part to realize four routes of pwm drive pulses with dead band of the control system
其次，通過對整個系統諧振頻率變化的分析和研究，設計了以鎖相環cd4046為核心的鎖相環控制電路，同時，在綜合比較鎖相環控制、模糊控制以及模糊控制和鎖相環復合控制三種控制演算法的基礎上，進行了系統模擬，得出採用復合控制可使跟蹤電路既具有鎖相環路較好的穩態性能，又擁有模糊控制較好的動態性能，系統魯棒性能好，同時也提高了逆變器的效率。 -
Next, in order to comprehand the electromagnetic characteristics and the dynamic characteristics of the new type of magnetic micromotors, the dissertation applied the concept of the magnetic scarlar potential of the irrotational magnetic fields and set up the mathmatic model for the inner magnetic field of the new type of motors from the basic equations and the boundary conditions of the motor magnetic field. oh the basis of the mathmatic model, the dissertation analized the various qualities of the magnetic field of the air gap between the rotor and the stator and gave a detailed calculation of the air gap ' s magnetic potential, magnetic field intensity, magnetic induction, the shape of the magnetic scarlar potential level surface, the distribution of the magnetic circuit, the magnetic induction the self - inductance and the mutual inductance of the coils
其次，為全面了解這種新型電磁電機的電磁特性和動力特性，本文從電機磁場的基本方程及其邊界條件出發，應用無旋磁場的標量磁位概念，建立了端面搖擺式電磁微電機內部磁場的數學模型，並以此為基礎，詳細分析了電機氣隙磁場的各方面性質，對氣隙磁場的磁標位、磁場強度、磁感應強度、等磁位面形狀、電機工作磁路的分佈、電機的工作磁通量以及激勵繞組的自感和相互之間的互感進行了詳細的分析計算。 -
It combained potentiostat, potentiostatic circuit instrument and ac impedance measurement organticace, which can measure usual dynamic potentio - scan, experiment of dynamic potentio - scan, but also unique measurement of ac impedance measurement, also, this new type electrochemical workstation can carry on complex experiment, sucn as potentio / current scan ac impedance measurement procedural measurment, life - span - circle ac impedance measurement procedural measurement in order to fullfill the goal of track and analysis of parameter in various electrochemical conditions. this graduation thesis indicate the structure, function of the multifunct - ional electrochemical workstation
它把恆電位儀，恆電流儀和電化學交流阻抗分析儀有機地結合到一起，既可以做常規的基本測試如動電位掃描、動電流掃描試驗和電化學交流阻抗測量，也可以做基於這三種基本試驗的程式化試驗，如恆電流充電-電化學交流阻抗測量，電池壽命循環試驗-電化學交流阻抗測量試驗，從而完成多種狀態下電化學體系的參數跟蹤和分析。 -
And experiment was based on the simulation, the results show that charge circuit and uplifted circuit both was adopted the same circuit, which can realize energy bi - directional flow, also have low switch ullage and high dynamic response
在此基礎上進行了實驗研究，模擬和實驗結果表明，該裝置升壓和降壓只採用同一個主電路，即可實現能量的雙向流動，且具有低開關損耗和較高的動態響應。 -
Circuit simulation demonstrated that the dynamic and static performances of buck converter controlling by sliding mode are better than that of pwm converter
電路模擬表明，滑動模控制的buck變換器的許多動態性能和靜態性能都優于pwm控制的buck變換器。 -
On one hand, it may exert damping on the armature of torque motor and overcome self - excitation of jet pipe. one the other hand, it may enlarge magnetic permeability of working clearances and improve magnetic circuit efficiency of torque motor to boost dynamic response speed of servo valve
一方面可增大力矩馬達工作氣隙部分產生的阻尼，從而可以抑制射流管的自激，另一方面又可增大工作氣隙的導磁率，改善力矩馬達部分的磁路效率，從而提高伺服閥的動態響應速度。 -
In this paper, the design of a specific chip for circuit emulation based on ip is put forward and realized and the main functional modules and the key algorithms including an all - digital adaptive clock recovery method and a dynamic depth buffer algorithm are described in detail
文章根據相關標準提出並實現了一種電路模擬專用晶元的設計方案，並對其中主要功能模塊和關鍵演算法作出了詳細說明，包括一種全數字的自適應時鐘恢復方法、動態深度緩沖演算法等。 -
The thesis mainly studies the correlatively pivotal technique and theory during the design process of computer control system for short circuit experimentation, which is an important part of dynamic simulation laboratory
本論文主要基於短路實驗控制系統，對系統設計開發過程中涉及的關鍵性技術和理論作詳細的研究和探討。 -
Because of the digitally rebalanced circuit, the sensor is capable of achieving better static and dynamic characteristic, higher sensitivity and stability. in this paper, the propagation path of light in the step index fiber and graded index fiber is introduced firstly. then the paper sets up the coupled power model and develops the coupling function
在文中，首先介紹了光線在階躍型光纖和梯度折射型光纖中的傳播路徑，以及在一端鍍有反射膜的1 4波節長度的grin透鏡中的成像規律，並推導了光功率耦合函數。 -
( 3 ) modeling of the asymmetrical half bridge converter in the thesis, a small average circuit model of asymmetrical half bridge converter power stage is established by method of state space averaging. in term of it, a system model of total converter is founded. the characteristic of stabilization and dynamic is analysed and the compensator is designed basing of it
（ 3 ）不對稱半橋dc dc變換器的建模分析採用狀態空間平均法建立了不對稱半橋變換器功率級的小信號平均電路模型，在此基礎上建立整個變換器系統模型，對系統的動態特性和穩定性進行了分析並設計了補償器。 -
The principle and the mechanical structure of the air - gap inductance - type transducer are analyzed in this article, and the static parameters are calibrated. dynamic calibration is applied to air - gap inductance - type transducer which is not good in dynamic capability, to obtain the dynamic parameters of the transducer and its measuring circuit. based on the result of the dynamic calibration, the transducer and its serving circuit are modeled so that the method of how to improve the dynamic performance can be found
本文對現有氣隙式電感傳感器在原理和機械結構上作了深入的分析，對其參數進行了靜態標定；並且針對常規電感傳感器動態響應低，不宜用於快速動態測量的缺點，引入測試系統動力學的思想，設計了一套動態校準系統，對現有傳感器進行多次動態校準，根據動態校準的實驗結果對現有傳感器建立數學模型，得到現有傳感器的動態特性；在此基礎上，根據磨床工件在線檢測的要求，設計一個硬體補償系統來提高整個測試系統的動態特性。 -
To avoid the serious electromagnetic interferer, the analog signals are transformed to frequency pulses which are transferred to the kernel of the system. in the measure of the groove voltage, the method of float - ground is adopted to avoid the high common signal and the range switch circuit is designed to solve the conflict of the wide dynamic range and the high precision. least square curvefit is adopted to reduce the system error
鋁電解生產現場電磁干擾非常嚴重，為此我們將需要測量的模擬信號就近轉換為頻率脈沖后再傳送到控制核心；採用浮地接入方式消除槽電壓信號中的共模成分；設計了量程自動切換電路以解決槽電壓的動態范圍寬和測量精度高的矛盾；用最小二乘法進行曲線擬和以降低測量的系統誤差。 -
The study has completed the design of two - phase inverter and made up of the two - phase inverter - motor system for experimental use it is a variable frequency adjustable speed system with a open - loop control of rotational speed, which consists of voltage - controlled oscillator circulating assign device inverter circuit and two - phase induction motor a accurate mathematical model is set based on the whole system, and simulator program of dynamic and steady condition is established, which is used to calculate the dynamic and steady performance by kron and symmetrical coordinate converter by simulator calculation and experimental research with specific parameter of the system, a comparison is made between predicted and experimental characteristics, experimental measurements are shown to compare closely with corresponding theoretical result it is compared with some variable frequency adjus table speed system comprising inverter and single - phase induction motor from the system efficiency torque pulsation and the effect of two - phase inverter capacitance based on the conclusion, harmonic cancellation pulse width modulation control of a two - phase inverter - fed induction - motor drive system is researched, which cancelled the low harmonic and improve the system performance
通過對電機的kron變換和對稱分量變換，建立了系統較精確的數學模型，編制了系統動態及穩態運行的模擬計算程序分別計算系統的動態和穩態性能。通過對系統的具體參數進行了模擬運算和實驗研究，實驗和模擬結果進行比較，說明實驗和理論較為一致，並從系統效率、轉矩脈動及兩相逆變器電容的影響等方面與各種逆變器和單相異步電動機組成的變頻調速系統加以比較。在此基礎上，對兩相逆變器供電-異步電動機系統使用諧波抑制pwm控制進行了研究，由於減少了低次諧波，改善了系統性能。 -
Thirdly, the relative theories of the limiter and rectifier are studied. in order to make the passive responder work stably under the conditions of large dynamic range of the receiving power and the high efficiency requirement, a two - stage limiter circuit and a voltage - doubler rectifier circuit with several diodes parallel are developed
3 ，對應答器地面裝置中的能量轉換電路進行了研究，針對應答器地面裝置接收到的載波功率具有大動態范圍的特點以及系統能量轉換的高效率要求，設計了一種兩級級聯二極體限幅電路和多管並聯的倍壓整流電路。 -
The voltage - controlled oscillator and the dual - modulus prescaler are the most crucial blocks in the pll frequency synthesizer. two kinds of voltage - controlled oscillator ( the quadrature voltage - controlled oscillator based on symmetrical spiral inductors and differential varactors, and the voltage - controlled oscillator with wide tuning range based on mos varactors ) and two kinds of prescaler ( the prescaler using phase - switching techniques, and the prescaler using dynamic circuit techniques ) are proposed. then, the complete pll frequency synthesizer is implemented, in which
壓控振蕩器和雙模預分頻器是鎖相環型頻率合成器中最關鍵的兩個模塊，本論文分別實現了兩種類型的壓控振蕩器（採用對稱螺旋型電感和差分二極體型容抗管的正交壓控振蕩器和使用mos型容抗管的大調諧范圍壓控振蕩器）和兩種類型的雙模預分頻器（使用相位開關技術的雙模預分頻器和使用動態電路技術的雙模預分頻器） 。 -
Sparse - tree architecture enables low carry - merge fan - outs and inter - stage wiring complexity. single - rail and semi - dynamic circuit improves operation speed. simulation results show that the proposed adder can operate at 485ps with power of 25. 6mw in 0. 18 - mu m cmos process
具有代表性的并行前綴進位結構有kogge - stone樹brent - kung樹han - carlson樹和knowles樹等，一些高性能的加法器也由此被設計出來。 -
A new method based on fwcm ( fast wavelet collocation method ) for time domain steady state simulation of nonlinear dynamic circuit is proposed
摘要本文提出一種基於快速小波配置法（ fwcm ）的非線性動態電路時域穩態模擬方法。 -
After having analyzed the theory of the calculator circuit thoroughly, the author made use of the characteristic of the calendar circuit and put forward a new design method, namely replacing the static circuit with the dynamic circuit to reduce the area of whole chip. now the author has finished the design of the calendar circuit and accomplished the layout design with the full - custom method
本文作者在透徹分析計算器原理的基礎上，利用萬年歷電路的工作頻率的特點，提出了以cmos動態門代替靜態觸發器的設計方法，獨立設計出萬年歷部分電路，將其與計算器部分電路緊密融合，構成一塊完整的數字大規模集成電路，並以全定製的方法實現了整個晶元的版圖設計。
分享友人