elongation percentage 中文意思是什麼

elongation percentage 解釋
伸長率
  • elongation : n. 1. 延長，伸長；延長線；伸張度。2. 【天文學】距角。
  • percentage : n 1 【數學】百分法；百分數；百分比，百分率。2 比例，部分。3 【商業】手續費，傭金。4 〈俚語〉賺頭...
  1. Used for testing the segment evenness of cotton lap at specified length, at the same time testing the weight and percentage of elongation of cotton lap

    用於檢驗棉卷在規定長度片段間的均勻度，同時測定棉卷的重量及伸長率。
  2. Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great

    採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。
  3. The results showed that the grain refining by the trace amounts of titanium could improve the tensile stress, percentage elongation and fracture toughness, but had little influence on their yield stress

    結果表明， ti對晶粒的細化可以大幅提高試驗合金的抗拉強度、延伸率和斷裂韌性，但對合金的屈服強度影響不大。
  4. The results show that, with the quenching temperature ( 270 ~ 380 ) increasing, the carbon content and percentage content of retained austenite increase first and then decrease, which are up to a maximum value at 360 ; the tensile strength of adi decreases ; the elongation and impact ductility of adi increase first and then decrease, which are up to a maximum value at 360 ; but the hardness of adi decreases first and then increases, which is up to a minimum value at 360

    結果表明，在試驗溫度范圍內（ 270 ~ 380 ） ，試樣中殘余奧氏體的含碳量及其含量隨著等溫淬火溫度的升高先增大后減小，均在360等溫淬火時出現最大值；抗拉強度隨著等溫淬火溫度的升高而逐漸降低；伸長率和沖擊韌度隨著等溫淬火溫度的升高先增大后減小，在360等溫淬火時出現最大值；硬度則隨著等溫淬火溫度的升高先減小后增大，當360溫淬火時硬度最低。
  5. Moreover, rare earth ceo2 can clean the melt and the face of reinforced particles and improve the wettability between the reinforced phase and melt and the property of material. proper additive mg and rare earth can improve the hardness, wear - resisting property tensile - strength, elongation percentage of tic / al, tic / al - si composite

    加入適量添加劑mg和稀土ceo _ 2使原位tic al ， tic al - si復合材料的硬武漢科技人學碩1 ：論義度、咐磨性、抗拉強度、延伸率得到很大的提高。
  6. Evaluation of uncertainty of measurement in testing for materials at ambient temperature has been discussed, including tensile strength ; lower yield strength ; proof strength, non - proportional extension ; percentage elongation after fracture and percentage reduction of area

    摘要文章介紹了金屬材料室溫拉伸試驗測量結果不確定度的方法，內容包括抗拉強度、下屈服強度、規定非比例延伸強度、斷后伸長率和斷面收縮率等性能指標。
  7. The wire size is between0. 1 ? 0. 35. those soft wire materials with their wire sizes 0. 10 are manufactured by special methods, and can have their percentage elongation higher than 15 %. the company is a special manufacturing factory in the market, and the filament is the ideal material for knitting and shielding materials

    線徑可從0 . 1 ? 0 . 35 ，其中我廠產品0 . 10軟態線材以特殊專有方式生產，延伸率可達15 %以上，是市場上專業的生產廠家，是作為編織屏蔽材料的理想用材。
  8. With the increased of pego percentage in blend films, the broken strength, the initial tensile modulus and the broken power decreased, but the elongation at break increased

    隨著pego的加入，共混膜的斷裂強度和拉伸初始模量下降，斷裂伸長率提高，斷裂功減小。
  9. 434 we shall take the sample to test its physical properties ( mechanical properties, tensile strength, yield point, percentage elongation, reduction of area, impact value, brinell hardness )

    我們將取樣試驗其物理性能（機械性能、抗張強度、屈服點、延伸率、斷面收縮率、沖擊值、布氏硬度） 。
分享友人
分享到 Line

分享到臉書