embedded mode 中文意思是什麼

embedded mode 解釋
嵌入方式
  • embedded : 埋入的
  • mode : n 1 法，樣，方法，方式。2 模，型；樣式，體裁，款式；習慣。3 風尚；〈the mode〉流行，時髦。4 【語...
  1. Aiming at the function and performance limitations of traditional special cnc or current pc - based open - structure cnc, a brand - new cnc platform designing scheme of multi - layer open - architecture is presented, based on embedded - mcu calculation and management core, and three kinds of expanding mode of software, hardware and interface. by using double system working ram and boot rom technology, an independent re - development interface is set on the hardware platform to realize customized function ’ s simulations and verifications online, which makes all the expanding or re - configuring on basic cnc platform are all safe and restorable

    本文針對傳統專用數控系統的結構封閉、交互形式不通用和配置擴展不靈活方面的劣勢以及當前pc模式開放結構數控的體積龐大、開放程度不高和實時可靠性不強的局限，創新性地提出了以基本cnc框架+軟體、硬體和介面三種擴展形式為特徵的層次化開放結構的嵌入式cnc硬體平臺，並採用雙存儲區技術進行了cnc系統在線模擬校驗機制和安全保護機制的方案設計。
  2. ( 2 ) resolute correlatively key technical problems, such as : embedded modem, embedded tcp / ip protocol, embedded webserver, gateway rg mode, lan inside network communication protocol, physical interface technology, total system miniaturization design and so on

    （ 2 ）解決相關關鍵技術難點，主要包括：嵌入式modem 、嵌入式tcp / ip協議棧、嵌入式webserver 、家居網關rg模型、局域網內部網路通信協議、物理層介面技術、智能應用終端改造途徑、整個系統小型化設計等。
  3. It includes chip selection, schematic circuit design, cpu selection and configuration, startup of the system, selection and configuration of embedded operation system, selection and configuration of tcp / ip software. it also describes some driver programming techniques of network controller. part 3 ( chapter 5 and 6 ) briefly introduces encryption technology and the ipsec protocol system, including architecture, mode, security association, security policy, implementation mode, processing of in / out packet, esp ( encapsulation security payload ), ah ( authentication header ), ike ( internet key exchange ) etc. the security requirements of embedded - networking is also analyzed

    本文首先探討了嵌入式網路的原理和設計要求，接著介紹了本文所開發的嵌入式系統的硬體平臺的設計（包括處理器的選擇與配置、存儲器的選擇和io設備的選用等） ，系統的啟動（包括bios和dos的啟動以及嵌入式操作系統vrtx的配置和引導） ，網路及其安全服務的實現（包括嵌入式協議棧usnet的選取、底層驅動程序的設計和安全協議ipsec的分析與實施） 。
  4. The first chapter discusses the concept of embedded system and explore mode as a whole ; the second chapter recommends the feature of real - time operation system, especially the psosystem, the basic system of this item ; the third part gives the principle of gateway ; the forth part lists the item process guideline, and then introduces the design of hardware and software and item test procedure, and at last analyzes the improvement plan according to test

    第二章介紹了嵌入式操作系統的特徵，並詳細介紹了本項目的核心基礎psosystem 。第三章以數據通信為著眼點介紹了網關的工作原理。第四章提出了項目開發指標，並從硬體設計、軟體開發和項目測試等方面詳細介紹了項目開發過程，給出了測試結果，並分析了項目的改進方案。
  5. At the early age of embedded system history, many real - time operating system use multi - task sharing single address space mode, which means kernel and application run in the same priviledge and application can access the whose address space with full pomission, for the limited performance and hardware resource

    在嵌入式系統發展早期，由於硬體資源和性能有限，很多實時操作系統採用的是單地址多任務空間模式，即內核和應用都運行在同一特權級，應用程序可以無限制的訪問整個系統地址空間。
  6. In this paper, on the foundation of synthesizing engineering practice and study result of planted bar technique by chemistry glue on the domestic and international, embedded experiment study and theories analysis are done about bonded anchor behavior of chemistry planted bar anchorage behavior in this paper, the experimental results of 32 pulling resistance test ( meiya z3530 ) are given, considering some factors to affect bonded anchor behavior of chemistry planted bar such as the strength of concrete anchorage lengths diameter of steel bar and holes thickness of the protecting layer confecting circumstance of the hoop bar and quantity of construction especially which is very easy to be neglected and so on, and bonded anchor mechanism failure mode load carrying capacity and slide behavior are analyzed in - depth

    本文在綜合國內外化學膠植筋技術的工程實踐和研究成果的基礎上，對化學植筋的粘結錨固性能作了較深入的試驗研究和理論分析。文中通過32個化學膠（美亞z3530 ）植筋試件的拉拔試驗研究，考慮混凝土強度、錨固長度、鋼筋植筋、鉆孔孔徑、保護層厚度、箍筋配製情況及施工質量等因素對植筋粘結性能的影響，特別是植筋的施工質量對粘結性能的影響是比較容易被忽視的因素，對化學植筋的粘結錨固機理、破壞形態、承載力及滑移性能作了比較深入的剖析。
  7. Firstly, based on price theory and transmission service theory, the thesis compares embedded pricing mode with incremental pricing mode, points out their advantages and disadvantages : though embedded pricing mode can recover transmission cost, but can not supply good economic signal. while incremental pricing mode can bring strong economic signal, but cannot recover transmission cost

    首先，論文研究了參與定價模式和微增定價模式的多種輸電定價方法，指出雖然參與定價模式大多能回收輸電成本，計算簡單，價格穩定，但不能給用戶正確的經濟信號；而微增定價模式雖然能給出正確的經濟信號，卻對輸電固定成本回收無能為力。
  8. The system is embedded software, working on the wdpf ii control system of westinghouse corp. of usa and communicating to the control system real time, calling the global database, using some tools of wdpf system. in order to improve ocs working efficiency, we have to research the wdpf control system constructions, network structure, data type, database structure, communication mode, system tools applying and so on. so ocs uses the wdpf ii resource as possible as it can in developing program

    由於本系統為典型的嵌入式軟體，工作在西屋公司wdpf控制系統之上，並與控制系統實時保持通信，隨時訪問系統的全局數據庫，同時訪問利用該系統的各種工具軟體，所以在軟體設計前對wdpf自動化控制系統的系統組成、網路結構、數據類型、數據庫結構、通信方式、系統軟體應用等方面都作了非常仔細的研究並在系統編制時對數據及設備資源作了最大的利用。
  9. This paper aims at the request of distribution automation and the disadvantages of existent ttu products and puts forward a scheme of ttu design : dsp ic tms320lf2407a of ti ltd. is chosen as a controller because of its high performance ; a three - phase power / energy ic developed by sames ltd. is used as a measure module to simplify the hardware circuit and software program ; the embedded modem and rs485 / rs232 mode communication interfaces are designed to make the data transfer more flexible and effective ; the 101 communication protocols of international electric power standard are adopted to improve its compatibility

    本文針對配電自動化的要求及現有ttu產品的不足，提出了一種基於dsp的配電變壓器遠方終端單元的研製方案：微控制器選用ti公司高性能定點dsp晶元tms320lf2407a ；使用sames公司推出的三相電能計量晶元sa9904a作為測量模塊，簡化了硬體電路和軟體編程；採用siliconlaboratories的嵌入式modem 、 rs485 rs232等多種通信方式，使數據傳送變得靈活、高效；為了提高設備兼容性及通用性，通信協議採用國際電力標準101規約。
  10. Firstly, the current testing localization in the detection of electric bow is analyzed and the new system ' s whole construction developed in this thesis is introduced ; in the 2rd chapter, the embedded 110v dc power supply is analyzed and constructed, and with experiments, some dissonant results such as the fluctuation of output pwm ( pulse width modulation ) pulses, the power noise added to output voltage, and the drop of output voltage have been analyzed and the problems have been broken down one by one ; in chapter 3, stepping motor ' s drive has been systematically dissertated, and combing stepping motor ' s subdivided drive technology, the author develops an intelligent mini - step driving circuit using a main - sub microprocessor structure, which is validated in the hybrid stepper based system ; in the 4th chapter, liquid crystal driving and displaying technology is specified in detail, with one sort of lcd modules ( tlm12864h ), the author develops an feasible circuit for the new testing system, designs a menu mode based program struc ture and brings here some programming codes using franklin c51 programming language ; in chapter 5, the above built system is used in the electric bow ' s practical detection, and the differentiating rate of this system is analyzed

    論文首先分析了目前機車受電弓檢修方式存在的局限並概述了本論文研製的受電弓測試系統的體系架構；第二章對系統內置110v直流控制電源進行了分析和設計，結合試驗對輸出pwm振蕩、輸出電源噪聲大、輸出電壓下跌等現象進行了分析並提出解決措施；第三章論述了步進電機的驅動，結合步進電機微步驅動技術研製了基於上下位單片機組的混合式步進電機智能驅動電路，並在試驗中得以驗證；第四章詳述了液晶驅動及顯示技術，利用一款液晶顯示模塊tlm12864h研製出本系統用液晶顯示電路，設計了菜單式的程序結構並以franklinc51編程方式給出部分子程序代碼；第五章則將以上構建的整個系統應用在機車受電弓的實測中，並對測試解析度進行了分析。
  11. The condition monitor system adopt hiberarchy, it was composed of head computer, monitor computer, periphery board and some circuit, the system can work in three different mode accord the different condition, the monitor computer and periphery board use the pc / 104 embedded module to make the system have the strong anti - vibratility and high ability of real time disposal ; in the system, we adopt the self - examination, redundancy design and some measures of software and hardware anti - jamming to make the system have strong ability of anti - jamming and high reliability, those all make the system adapt the worst work condition of the engine and realize the real time monitor of engine condition

    該狀態監測系統採用了分級結構，由上位機、下位機、外圍卡板和各種電路組成，可以根據不同情況在三種方式下工作。在下位機和外圍卡板的設計中採用了pc 104嵌入式模塊，使得系統具有較強的抗震性和實時處理能力；在整個系統中還採用了軟硬體抗干擾措施，並進行了自檢系統和冗餘結構的設計，使得系統具有較強的抗干擾能力和較高的可靠性，經過這些設計，使系統可以適應發動機運行過程中的惡劣條件，實現對發動機狀態的實時監測。
  12. For the image acquisition of optical scan mode, normally, ccd image sensor is used to capture image, but in our system, due to the system request of micromation and high integration, cmos image sensor is adopted as the image collection device, and then the thesis gives a interface circuit between the chip and dsp and a control solution of image collection ; toward the information storage in our solution, dsp is directly linked to usb host chip and it is the dsp that accomplishes the processing of usb protocol and interface control so as to reduce the cost, minimize product cubage and consequently meet the requirement of system micromation ; at the same time, the thesis probes preliminarily into usb otg ( on - the - go ) technology, which offers an approach between embedded machines including pda, mobile phone, printer, digital camera and so on ; in addition, some attempts on the other application area with tms320vc5402 which was commonly used to voice processing and static image processing are done, for example, to arrange the chip to control lcd module directly

    在圖像的光電掃描輸入上，傳統方案大部分採用ccd型圖像傳感器，而在本方案中，根據系統微型化、高集成的特點，使用了cmos圖像傳感器作為攝像器件，並且設計了該晶元與dsp的一種介面電路以及圖像採集控制方案；在信息存儲上，本方案採用dsp直接與usbhost晶元連接，由dsp處理usb協議和介面信息，從而降低了系統成本、縮小了產品體積，滿足了系統微型化的要求；同時本論文也對usb - otg技術進行了初步探討，利用此項技術，不再需要計算機作為主機，就能實現在pda 、移動電話、印表機、數碼相機等嵌入式應用之間直接互聯通信；另外也對廣泛用於語音處理和靜態圖像處理的tms320vc5402其它方面的應用進行了嘗試，比如直接控制液晶顯示器等。
  13. Stand - alone is the preferred mode for many embedded applications

    單機模式是許多嵌入式應用程序的首選模式。
  14. And the inverter becomes smarter. during the designing, the pulse - processing ciucuit is preset which processes the feedback pulse from photoelectric encoder for close - looping the system in future. by using the circuit and quadrature mode of timer 1 in 80c196mc, incremental encoder can be embedded into the velocity regulation system more easily and the domain the inverter can be used in is enlarged too

    在系統設計過程中，考慮到了變頻調速器進一步改進為閉環系統的需要，在電路中預設了光電碼盤反饋脈沖的處理電路，通過這個電路的處理，並利用80c196mc中定時計數器1的90相移計數工作方式，可大大簡化使用增量式光電碼盤時脈沖處理的復雜度，這也擴大了本文中變頻調速器的應用范圍。
  15. With slight modification, it can also be used in video audio devices. the transport technology of this design includes web server mode and streaming server mode. configuration and test method of both the two modes are valuable to future research and implementation of embedded video collecting system

    本設計的視頻傳輸採用了websever和streamingserver兩種方案，無論是websever的設置及測試方法還是streamingserver設計原理及測試方法，對于以後嵌入式網路視頻採集系統的研究及應用都具借鑒意義。
  16. The design of network video collecting system proposed in this thesis is based on embedded hardware developing platform with motorola mcf5272 chipset as center chipset, and uclinux as embedded system as software developing platform. after collecting video data through a usb camera, the system compresses the data in jpeg picture format and mpeg - 4 video format. then with the embedded web server and streaming server, it establishes connection with client in c / s mode, which enables the client to view the video through browser or normal media player remotely

    本設計所提出的網路視頻採集系統的設計是在以motorola的mcf5272晶元為主晶元的嵌入式硬體開發平臺配以uclinux作為嵌入操作系統的軟體開發環境下，通過一個usb介面的攝像頭輸入原始的視頻數據，在嵌入式板上分別採用了jpeg圖像格式壓縮和mpeg - 4視頻格式壓縮對原始的視頻數據進行處理，最後通過內置的web服務器和流式媒體服務器，採用c / s的方式與客戶端建立連接，使客戶端在只要能上網的地方就能通過瀏覽器或是普通的mediaplayer播放器觀看到服務器端採集到的影像，具有十分廣泛的應用前景。
  17. In part 2 of this three - part series, you ll turn the classes - which you created to access the database in part 1 - into three different applications using derby s single - user embedded mode, its multiuser network mode, and a combination of the two from within a web environment

    在本系列教程第2部分中，我們將把第1部分中創建的數據庫訪問類轉換為三種不同的應用程序，分別使用derby的單用戶嵌入模式、多用戶網路模式和web環境下兩種模式的結合。
  18. Taking can - bus driving as a instance and using embedded microprocessor ' s hardware character, we provide the managing mode of multi - task communication. semaphore, mailbox and message queue is used in this paper to realize the communications mechanism of multi - task

    利用嵌入式微處理器的硬體特點，以can總線驅動為例，提供系統調用多任務通信管理方式，並使用基於信號量、郵箱、消息隊列的通信機制進行多任務間的通信。
  19. We first put forward the file system of hierarchy structure through an object - oriented programming approach. to deal with great amount of data from geographic information and the need of fast access, we design a kind of professional embedded gis data structure to combine the quad tree storage format and the deploying mode of the file system. this method can implement the fast access for geographic information data

    通過面向對象的程序設計方法提出層次體系架構的文件系統；並針對地理信息數據量大的特點和快速空間存儲的需求，提出了一種將四叉樹存儲格式與文件系統的調度方式相結合的嵌入式gis專用數據結構，實現了地理信息的快速存取。
  20. In addition, the control of spontaneous emission of a three - level atom embedded in photonic crystals was investigated in this paper, because the model of two - level atom is siple. as it shows, the properties of spontaneous emission depend not only on the relative position of the resonant frequency from the edge of the photonic band gap and the photonic mode density but also on the intial atomic state

    二能級畢竟是最簡單的模型，故在最後，還對光子晶體中三能級原子的自發輻射特性進行了研究。結果表明，其自發輻射除了依賴于原子上能級與光子頻率帶隙邊緣的相對位置或光子態密度外，還依賴于原子的初始狀態。
分享友人
分享到 Line

分享到臉書