entry temperature 中文意思是什麼

entry temperature 解釋
進口溫度
  • entry : n 1 進入，入場；入城；（演員）出場。2 入口；門口。3 通道，路口；河口。4 登記；記載；申報；記錄；...
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. 4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity

    結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。
  2. On the other hand, in winter, it should be taken the adequate change in production techniques such as the increase of pit entry temperature in the first steamer, the decrease of pit stepping times, the addition of saccharifying enzyme and dry yeast, and the increase of starch content etc. to ensure good fermentation of fermented grains and further to stablize and improve product quality

    同時，在冬季生產中，要採取適當提高第一甑大（米查）的入池溫度、減少殊窖、添加糖化酶和乾酵母、提高澱粉濃度等工藝措施，保證糧醅的良好發酵，穩定和提高產品質量。
  3. The limestone particles are heated rapidly to high temperature upon entry into the boiler furnace.

    當石灰石顆粒一進入鍋爐爐膛，就迅速被加熱到高溫。
  4. Sow series single stage double entry pump is a horizontally split volute centrifugal pump, mainly used to handle clean water or liquids similar to water in physical and chemical properties, temperature not above 105

    Sow系列單級雙吸泵系水平中開蝸殼式離心泵，主要供輸送溫度不高於105的清水或理化性質類似於水的液體。
  5. The temperature - control accuracy of gas chromatograph, mode of entry of liquor samples from vaporizing chamber after vaporization to chromatographic column, dnp chromatographic column efficiency, and liquor analysis time length etc. are the factors influencing the accuracy of the data in the analysis of liquor microconstituents by gas chromatograph

    氣相色譜儀器的控溫精度、酒樣進入汽化室汽化后進入色譜柱的方式、 dnp色譜柱效、酒樣分析時間的長短等都是影響氣相色譜儀分析白酒中微量成分數據準確性的重要因素。
  6. Shanghai asiahope trade co., ltd their subordinate of the ceramics factory, devoted to developing the modern ornament materials ; pursue natural art is combined with the new concept of the modern life, found and smelt the ceramic brick of crystal inferiorly, one layer of complete hand mades of surface crystal of the brick, after the high temperature is fired, the surface of the brick does not have regular crystal crackle to produce naturally, the products have more than more than ten seed colors, is suitable for hotels such places as the hall and top - grade bar, swimming pool, bathroom, entry wall, kitchen, sitting room background wall, etc., deep since smelting brands and appearing on the market inferiorly welcomed by the market

    上海遜豪貿易有限公司其下屬擁有自己亞冶陶瓷廠，致力於研製現代裝飾材料，追求自然藝術與現代生活新概念結合，所締造亞冶水晶陶瓷磚，磚的表面水晶層完全手工製作，經高溫燒制后，磚的表面產生自然無規則的水晶裂紋，產品有十幾余種顏色，適用於酒店大廳和高檔酒吧，游泳池、浴室、玄關墻、廚房、客廳背景墻等場所，亞冶品牌面市以來深受市場歡迎。
  7. Xiangjiao wrapped starter was produced by 90 % wheat and 10 % garden pea through grinding, starter - stepping and bank - entry fermentation ( adequate rise of starter - making temperature )

    摘要湘窖包包曲是以90 %的小麥加10 %的豌豆為原料，適當提高制曲溫度，經粉碎、踩曲、入房發酵而成。
  8. In allusion to the characteristic of ball mill that it is simple lag, serious inertia and nonlinear, and general control methods are hard to gain a good control impact, so a fuzzy control model is held up which is graded according to burthen, temperature of outlet, negative pressure of entry, and the coupling characteristic of the model is analyzed. finally a fuzzy control system is designed as the model

    而模糊控制策略大多應用於受控對象數學模型難以建立的場合，具有較好的穩定性和魯棒性，為此提出了按負荷、出口溫度、入口負壓順序分級預測的模糊控制模型，並分析了該模型的解耦特性，同時，按該模型設計了一種模糊控制系統。
分享友人
分享到 Line

分享到臉書