eutectic solidification 中文意思是什麼

eutectic solidification 解釋
共結固化
  • eutectic : adj. 【化學】低共熔的；易熔的；共晶的。n. 低共熔混合物，共晶體。
  • solidification : n. 團結；凝固；【化學】固體化（作用）。
  1. Effects of b on the eutectic solidification of hypereutectic al - si alloy

    合金共晶凝固過程的影響
  2. The rapid solidification process of pb - sn eutectic alloy is investigated with acoustic levitation and the maximum undercooling of 38k has been achieved

    採用聲懸浮無容器處理技術研究了pb - sn共晶合金在深過冷條件下的凝固規律。
  3. The containerless rapid solidification of al - 32. 7wt % cu eutectic alloy in drop tube is investigated. the " lamellar eutectic - anomalous eutectic " microstructural morphology transition occurs with the decrease of droplet size

    採用落管無容器處理技術研究了al - 32 . 7wt cu二元共晶合金在深過冷條件下的快速凝固規律。
  4. 4. under the directional solidification, either sub - or hyper - eutectic alloys, with the increase of growth rate, the lst dendritic arm spacing decreases and 2st dendritic arm spacing is restrained to some extent

    4定向凝固條件下，隨著凝固速率的增加，無論亞共晶合金或過共晶合金，一次枝晶間距減小，二次枝晶生長得到不同程度的抑制。
  5. The present thesis has carried out detailed investigation on the rapid solidification of undercooled bulk water and pb - sn binary eutectic alloy with acoustic levitation, and the various factors influencing the achievement of undercooling in sound field have been analyzed

    主要取得了以下幾方面的研究成果：研究了5 8mm的大體積水在聲懸浮無容器條件下的快速凝固行為。獲得了最大為24k的過冷度。
  6. In experiment, the dsc technique was used to analyze the effect of electric fields on the precipitate kinetic of al - li alloy solutionized with electric fields. the energy spectrum, tem and sem techniques are employed to investigate the elements solution, precipitates, fracture character, conductivity and vickers hardness. also, the solidification of al - cu eutectic alloy was conducted with the influence of electric fields

    在實驗上，利用dsc熱分析技術，分析了電場作用對al - li合金相析出動力學的影響；採用能譜成份檢測，透射電鏡和掃描電鏡等多種微觀檢測手段，對鋁合金的析出相，斷裂特徵、合金電導率和維氏硬度等性能在電場作用下的變化進行了系統的研究，並觀察了al - cu共晶合金在電場作用下的凝固組織。
  7. The effect of solidification rate on eutectic microstructure of high chromium cast iron

    凝固速度對高鉻鑄鐵共晶組織的影響
  8. The effect of solidification rate on the solidified structure, cooperation growth zone and microstructures such as tac rods volume fraction, tac rods average spacing, tac average transverse area and y phase in this eutectic composite were systematically investigated with lmc. the relationship between solidification processing controlling and solidification microstructure was established

    藉助金相技術、電鏡技術、圖象處理技術等多種分析測試手段，考察試樣的界面形態、組織特徵以及共晶形貌等多方面的凝固特性，建立了凝固過程式控制制與凝固組織的對應關系。
  9. That the alloying element mn and ti substitutes the atom of fe in the rich iron - phase ( al, si, fe ) and resumes the part of the element si in primary phase refines the second phase. at the same time, the volume percentage of second phase is increased. at the course of solidification, the alternating current field changes obviously the microstructure morphology of the al - 20si - 5fe - x alloy and the number of particle eutectic structure is increased

    合金元素mn 、 ti通過占據富鐵相（ al ， si ， fe ）中鐵原子的晶格位置，同時消耗部分初生相中的si元素，形成四元富鐵相（ al ， si ， fe ， mn ） ，細化了合金中的第二相，同時提高第二相體積百分數。
  10. It was found that the interface morphology of ni, cr, al - tac eutectic in - situ composite evolved from plan to cell and then to dendrite with the increase of solidification rate, if the gradient retained constant. in the same time, the eutectic microstructure also evolved from rod to cell and then to dendrite

    本工作發現，在溫度梯度基本保持不變的條件下，隨著凝固速率的增大， ni ， cr ， al - tac共晶自生復合材料的凝固界面由平界面向胞狀及枝狀界面逐漸轉化。
  11. In this paper, one high temperature gradient directional solidification apparatus with liquid metal cooling ( lmc ) was used. the technology parameter of preparation for ni, cr, al - tac eutectic in - situ composite was optimized

    本文採用lmc高溫度梯度定向凝固裝置，對ni ， cr ， al - tac共晶自生復合材料進行了深入的研究，優化了該種自生復合材料的制備工藝。
  12. L4in this eutectic composite. the volume fraction of tac could be changed with increasing solidification rate

    隨著凝固速率的增大， '相的尺寸越來越小，其形狀也越來越圓。
  13. 3. for the component of sub - eutectic, the cu - cr alloys are difficult to form complete eutectic tissue on the condition of non - equilibrium solidification. the general microstructure is of cellular primary a ( cu ) and circumference - distributed eutectic ( a + p ) where the former mainly acts as the conductor and the latter as the reinforce, together to be fibrous eutectic reinforced in - situ composites

    3在非平衡凝固條件下，亞共晶cu - cr合金凝固組織的一般特徵為柱狀的初生晶之間分佈著條狀的cu - cr共晶體，前者主要起導電作用，後者作為強化相，形成共晶纖維強化的自生復合材料。
分享友人
分享到 Line

分享到臉書