fan nozzle 中文意思是什麼
fan nozzle
解釋
扇形噴嘴-
14. no warranty will be delivered to such consumables as nozzle, cylinder body caulking, washer, seal ring, o - ring, motor brush, capacitor, bulb, fuse, battery, fan, belt, paper filter element, glass sheet, fuel and lubricant
下列消耗品：噴油嘴缸體堵頭，墊片密封圈o型圈電機刷電容燈泡保險熔絲電池風扇皮帶紙濾蕊玻璃板燃油和潤滑劑。 -
To meet the needs for wider surge margin of the turbofan engine, a new model was developed to predict the characteristics of the fan / high pressure compressor and turbine in this thesis. several ways, including, variable inlet guide vanes of the fan, variable guide vanes of the high pressure compressor, the variable inlet area ratio of the mixer and the nozzle areas, were presented to enlarge the surge margin of the turbofan engine. meanwhile, a method of combined variable geometries for optimizing controls of inlet guide vanes of the fan, guide vanes and the first two stators of high pressure compressor, area ratio of mixer and noz zle areas was established
為了滿足下一代作戰飛機對推進系統的性能和穩定性要求，本文建立了壓縮系統特性和渦輪特性的新模型，並分別採用改變渦扇發動機風扇進口導流葉片、壓氣機導流葉片和前兩級靜葉片、混合室進口處內、外涵面積比和尾噴管面積，研究了其對發動機性能和穩定性的影響，進而得出了渦扇發動機變幾何擴穩的方法，為發動機變幾何擴穩研究打下理論基礎。 -
Experimental constants include : ambient temperature 291k ~ 301k, rh 15 % ~ 21. 2 %, wind velocity 3. 2m / s at the nozzle position and horizontal to the spray fan, others are same as the fore experiment. the tendency of the two experiments results is consistent with the tendency from simulation. that indicate the improved shield spray is better than the original shield spray in reducing spray drift, and also more better than conventional spray without shield
風洞試驗參數：噴霧藥液為含1 bsf的水溶液，風速1 . 4m s ，風向垂直於噴霧扇面，溫度281k 288k ，相對濕度rh9 20 ；室內試驗參數：噴霧藥液為含2 bsf的水溶液，噴頭處風速為3 . 2m s ，風向平行於噴霧扇面，溫度291k 301k ，相對濕度rh15 21 . 2 ；分別在噴頭下風向噴幅外的空中和地面布點收集飄失和飄移沉積的霧滴量，作為評價減少霧滴飄失效果的指標：試驗結果表明：改進后的罩蓋噴霧減少霧滴飄失的效果好於雙圓弧未開口罩蓋噴霧，常規無罩蓋噴霧的霧滴飄失量大於開口罩蓋噴霧。 -
Motor nozzle : the product adopts hard alloy or carbon steel heat treatment and receives precision grinding and polishing by professional processing equipment. therefore, it boasts high resistance to flexure and to wear and is extensively applied in fields of series, fan, micro - motor and motor for wire coiling of stator and rotor
產品描述： ：此產品以超硬質合金或碳鋼熱處理為材料，使用專業加工設備精密磨削和拋光加工而成，有極好的抗彎強度、耐磨性，廣泛用於串激、風扇、微電機、馬達等行業的定子、轉子的線圈繞制上。
分享友人