feed regulator 中文意思是什麼
feed regulator
解釋
給料第器-
Coal feed regulator
喂煤調節器 -
Voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed
採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源 -
Abstract : voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed
文摘:採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源 -
Stitch regulation and reverse stitching : simply by turning the stitch regulator thumb screw and adjusting feed reversing handle, you can easily sew stitches of desired length or reverse stitshing
針距選擇及倒縫：調節針距，只用轉松固定螺釘，發動指示桿，即可縫紉不同疏密的針距或倒縫。 -
Some research about sensorless control of induction motors in recent years has been introduced in chapter one. in chapter two, a field - oriented control system with current regulator and voltage source inverter ( vsi ) is presented firstly, which is proved in theory that the voltage feed - forward decoupler can be omitted, the good decoupled control properties of flux current and torque current is also validated by experiments with speed - sensor based on f240dsp real system
論文第二章從異步電機的基本數學模型入手，介紹了一種基於轉子磁場定向的帶電流內環控制的電壓型逆變器輸出閉環矢量控制結構，在理論上證明了該模型可省略電壓前饋解耦環節，採用f240dsp晶元構建的帶速度傳感器實驗系統驗證了其定子電流勵磁分量和轉矩分量有良好的解耦控制特性。 -
When the suspended point is moving on the line in a kind of way, the pendulum will depart from the balance position. in order to minimize the swing movement of pendulum and minimize the consumption of power, a linear regulator is created for the system. finally, a optimum feed back status of speed is made
當懸掛點以某種規律沿直線運動時，會出現擺錘偏離原太原理工大學碩士研究生畢業論文平衡位置的情況，為了使擺錘在給定時間內在懸掛點行走一定距離的過程中擺角最小且能耗最少，本文將系統構造成為線性調節器，最終得到了使懸掛點移動速度最優的狀態反饋量
分享友人