fibre section 中文意思是什麼
fibre section
解釋
纖維截面-
This paper discusses how to improve expand section ' s lining of heavy - calibre and high - tempreture, the steel - fibre lining is improved to be the lining of firebrick and fireproof material, to avoide the lining drop and meet the needs of production
摘要闡述了如何將大口徑高溫膨脹節襯里由鋼纖維雙層襯里改為耐火磚加耐火澆注料結構,避免了襯里脫落,滿足了生產需要。 -
Test of mechanism of effect by polypropylene fibre on anti - crevice property amp; amp; normal section load - bearing capacity of bent reinforced concrete components
軸向力對預應力構件正截面影響的研究 -
In the numerical methods section, a finite element / control volume mold filling simulation, a tensor representation of fibre orientation and a finite element solution of the transient fibre orientation equations are combined in the program. the input data and output results are visualized by means of finite element software
程序中用有限單元控制體方法模擬模壓流動,用表徵纖維取向的張量和有限元伽遼金方法來解決瞬時纖維取向方程,用計算機圖形原理編程實現對smc流動軌跡、纖維取向分佈的計算機模擬。 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - tests - screen testing of ceramic alignment split sleeve by stress application - section 24 screen testing of ceramic alignment split sleeve by stress application
纖維光學互連器件和無源元件.基本試驗和測量程序.試驗.用施加應力進行陶瓷準直套管篩選 -
Optical fibre cables part 4 : section specification optical fibre composite overhead ground wire
光纜第4部分:分規范光纖復合架空地線 -
Insulating and sheathing materials of electric and optical fibre cables - common test methods - part 5 : methods specific to filling compounds - section 1 : drop point - separation of oil - lower temperature brittleness - total acid number - absence of corrosive components - permittivity at 23 oc d. c. resistivity at 23 oc and 100 oc
電纜和光纜的絕緣和護套材料.通用試驗方法.第5部分:填充化合物的專用方法.第1節:滴點.油分離.較低溫脆性.總酸度數值.無腐蝕性成分. 23時的電容率和23與100時的直流電阻率 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - examinations and measurements - measurement method for the hole location of a multiway connector plug - section 27 : measurement method for the hole location of a multiway connector plug
纖維光學互連器件和無源元件.基本試驗和測量程序.檢查和測量.多路連接器插頭的孔位測量 -
Used for cut the fibre or yarn into extremely thin cross section slices in order to observe its tissue & structure
用於將纖維或紗線切成極微小的橫斷面薄片,以觀察其組織結構。 -
Optical fibre cables part 3 : section specification - outdoor cables
光纜第3部分:分規范-室外光纜 -
For specific information about using a mass storage controller ( such as a scsi, raid, or fibre channel adapter ) with a driver that was supplied by the manufacturer, see the next section, " mass storage drivers and the setup process.
有關如何使用海量存儲控制器(例如scsi 、 raid或光纜適配器)和製造商提供的驅動程序的具體信息,請參閱下一節「海量存儲驅動程序和安裝過程」 。 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - tests - screen testing of return loss of single mode pc optical fibre connectors - section 43 : screen testing of return loss of single mode pc optical fibre connectors
纖維光學互連器件和無源元件.基本試驗和測量程序.試驗.單模pc光纖連接器回波損耗的篩選 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - tests - screen testing of attenuation of single - mode tuned angled optical connectors - section 40 : test method for screen testing of attenuation of single mode tuned angled optical fibre connectors
纖維光學互連器件和無源元件.基本試驗和測量程序.試驗.單模調整式有角度光纖光纜連接器衰減的篩選 -
In the same wafer, the fibre parameter was different along the radial. it was high at the edge and low in the center section
同一晶片上纖維沿徑向分佈有差異,邊緣纖維密度高,中心部位纖維密度低。
分享友人