filler volume 中文意思是什麼

filler volume 解釋
填料體積
  • filler : n. 1. 裝填者，斟酒人；注入器，漏斗；填充物。2. （雜志的）補白；電影補白短片。3. 雪茄煙心；（自來水筆的）吸墨管。4. 〈pl. 〉【化學】填料。5. （計算機的）進位填充數，填充位。
  • volume : n. 1. 卷，冊；書籍；【歷史】書卷，卷軸。2. 〈常 pl. 〉大塊，大量，許多。3. 體積；容積；分量，額；【物、樂】音量；強度，響度。
  1. Fitting the experimental data into the general effective media ( gem ) equation, a theoretical percolation curve was gained. a mathematical model was proposed which is based on the gem equation and the dilution effect of filler volume fraction due to thermal volume expansion

    使用有效介質普適方程（ gem方程）對實驗數據進行擬合，得到導電復合材料的理論滲流曲線，根據gem方程和基體的體積膨脹，建立起一個數學模型。
  2. In the volume change study, we found appropriate temperature is helpful for shrinkage control, and different lpas have different shrinkage control effects due to their dipole moment, tg, miscibility with upr and morphology after blending. there existed an optimal concentration range of poly ( vinyl acetate ) based lpas for shrinkage control. lpa was effective for shrinkage compensation in this range, on the other hand, lpa only acted as filler and the low profile effect vanished out of this range, however, for polystyrene based lpa, the more concentration the better shrinkage control

    在膨脹研究中，發現適當的溫度條件更有利於upr達到好的收縮控制效果；不同類型的lpa隨著偶極矩、玻璃化溫度、與upr的相容性、與upr的混合形態的不同，表現出不同的收縮控制效果；聚醋酸乙烯酯類的lpa - a存在一個最佳收縮控制的濃度范圍，在這個范圍之內， lpa起到補償收縮的作用；而在這個范圍之外， lpa的作用僅相當于填料，不能起到收縮控制。
  3. Pore parameters ( porosity and distribution of pore diameter ) of porous glass prepared by filler principle were measured and analyzed. they were mainly determined by the volume ratio and the particle diameter of the pore former in the green body. preparation and sintering process of the samples resulted in the difference between the porosity and the volume ratio of the pore former. they were also responsible for the deviation between the distribution of poer diameter and the particle diameter of pore former

    研究表明，利用填充法制備的多孔玻璃的孔參數（氣孔率、孔徑分佈）可進行設計與控制，多孔玻璃的氣孔率和孔徑分佈主要取決于成孔劑的體積比及其顆粒分佈，前者與後者之間的偏差取決于生坯制備及燒結過程。
  4. Liquid quantitative bottle filler with constant volume

    定容式液體定量灌裝機
  5. The curve of dynamic modulus versus the conductive filler volume percent showed that the dynamic modulus of the composites changed with increase of the filler volume percent and exhibited a transition phenomenon. it is believed that these results mentioned above were related to the filler dispersion and the interaction between filler and polymer

    通過研究動態流變行為對導電填料含量的依賴性，發現導電填料含量增浙江大學碩士學位論文加，體系的動態模量存在一轉變現象，被認為與顆粒在聚合物中的分散、填料與聚合物間相互作用密切相關。
分享友人
分享到 Line

分享到臉書