film abrasion 中文意思是什麼
film abrasion
解釋
膠片磨損-
The results show that the cohesiveness to cotton and polyester - cotton is better and that the property of size film is improved, especially the film abrasion resistance improved
結果表明：陽離子澱粉漿料對棉、滌棉黏附性良好，漿膜性能也有所改善，尤其是耐磨性能。 -
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。 -
Feature : abrasion resistant, stabilized shiny spvc film ; non - corrosive, resistant toacids, oils, moisture, humidity
好的防磨損性，穩定性好，無腐蝕性，防潮濕抗酸性，抗油性，具有光亮的pvc薄膜層。 -
Because self - compensation repairing film was produced more and more and was rubbing out more and more by friction, abrasion only occured in the self - compensation repairing film and negative abrasion was produced when the film producing abrasion speed was more than abrasion speed
由於在摩擦過程中自補償膜不斷生成，同時又不斷被磨損，當成膜率大於磨損率后，不僅磨損過程完全在自補償膜內進行，而且還會出現負磨損現象，產生自補償修復效應。 -
One of the important step of decreasing abrasion is lubracation, and the old lubrication oils only decrease the abrasion of the relative movement surface following with extending its " using life. it does n ' t produce self - compensation film on the friction surface and does n ' t produce zero abrasion and self - compensation repairing effects
減少磨損的重要措施之一是潤滑，然而傳統潤滑油只能起減少相對運動表面的磨損、延長其使用壽命的目的，而無在摩擦過程中產生自補償被磨損表面的能力，因此也就不可能產生零磨損效應和自修復效應。 -
Ideally lubricated contacts are separated by a fluid ( or perhaps a solid ) film, which prevents surface contact, thereby eliminating the wearing of surfaces by adhesion or abrasion
理想的潤滑是用液體（或者固體）的油膜將摩擦表面隔離開，防止金屬表面直接接觸，以便於保護表面不被粘附，或者磨損。 -
Taking gear without tooth face invalidation such as agglutination and abrasion as a precondition, and according to the relation between minimal oil film thickness and tooth face roughness of elastic liquid dynamic pressure lubrication theory, viscosity of gear lubrication oil was educed by reliability method in this paper, and the calculation formula has been elicited and applied
摘要以齒輪傳動不發生膠合、磨損等齒面失效為前提，根據彈性流體動壓潤滑理論的最小油膜厚度與齒面粗糙度的關系，用可靠性方法確定齒輪潤滑油的粘度，給出計算公式並進行了實例計算。 -
Lithograghy and its relative techniques play a very important role in mems fabrication processes, spin coating and baking are an indispensable working procedure before and after the lithography process. oven and hotplate are often employed in order to enhance adhesion between the film and the substrate, stabilize sensitivity of film and improve the abrasion resistance when the film touches a mask in contact exposure
均膠和烘乾是光刻工藝中不可缺少的一道工序，為增加膠層與矽片表面粘附能力，提高在接觸式曝光中膠層與掩模版接觸時的耐磨性能及穩定膠層的感光靈敏度，通常採用烘箱或熱板等加熱設備對光刻膠進行乾燥。 -
The coating film has predominant performance of hardness, glossiness, buildiness, waterresistance and abrasion resistance, especially yellowness resistance and high glossines
該產品具有非常優異的耐黃變性和非常高的光澤度。 -
Testing methods for paints - part 5 : mechanical property of film - section 8 : abrasion resistance rotating abrasive - paper - covered wheel method
塗料試驗方法:第5部分:膜的機械性能.第8節:耐磨性 -
Imaging materials - photographic film and papers - method for determining the resistance of photographic emulsions to wet abrasion
成像材料.攝影膠片和感光紙.測定攝影感光乳劑耐濕磨性的方法 -
Because of its good combination with the articles, it can be widely used in decorative plating ti film, protective coating such as dlc membrane on the glass, surface of mobile phone, magnetic hard disk etc. and tools plating tin or dlc etc. which are abrasion resistant, corrosion resistant and beautiful in appearance
由於薄膜與機體結合良好，可以廣泛的應用於各種裝飾鍍膜ti膜等，保護鍍膜例如在眼鏡片，手機手表面板，磁硬盤等沉積dlc膜，工模具鍍膜tin ， dlc等膜等，達到抗磨損，抗腐蝕，裝飾美觀的目的。 -
Testing methods for paints - part 5 : mechanical property of film - section 10 : abrasion resistance reciprocating test panel method
塗料試驗方法:第5部分:膜的機械性能.第10節:耐磨性 -
Testing methods for paints - part 5 : mechanical property of film - section 10 : abrasion resistance reciprocating test panel method erratum 1
塗料試驗方法.第5部分:薄膜的機械特性.第10節:耐磨性
分享友人