film-forming properties 中文意思是什麼
film-forming properties
解釋
成膜性能- film : n 1 薄層，薄膜；薄霧，輕煙；細絲狀的東西。2 【攝影】感光乳劑，照相軟片，電影膠片；影片。3 〈 pl ...
- forming : device
- properties : （特性）命令修改特性
-
As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn
理論工作方面，首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質，然後結合撞針型高壓小孔徑離心式噴嘴的結構特點，將其霧化加濕過程分三個階段進行機理上的研究，這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。 -
Then properties of the polysilane - polyacrylate gradient films were characterized. the mechanism of film forming process of polysilane - polyacrylate fgm was probed into as well
並對所制得的有機硅聚合物-聚甲基丙烯酸酯梯度膜的性能進行了表徵，對其成膜機理進行了探討。 -
Then properties of the polysilane - polyacrylate gradient film were characterized. the mechanism of film forming process of polysilane - polyacrylate fgm was probed into as well. the testing results indicated that adding p ( mma - co - ptris ) of different can improve the poor miscibility of pmma and ptris because p ( mma - co - ptris ) contained both pmma chains and organosilicone chains which joint pmma and ptris as a bridge
通過測試有機硅聚合物-聚丙烯酸酯共混梯度膜的結構，發現ptris和pmma的相容性較差，加入不同聚合比例的共聚物p （ mma - co - tris ）后相容性得到改善，並可以得到一面是丙烯酸酯端；然後結構漸變成有機硅聚合物端的梯度膜。 -
Finally, the results show that the addition of guar gum could increase the dose of modified starch, at the same time, the film - forming properties and adhesive force are improved
結果表明，瓜爾膠的加入能提高變性澱粉的用量，有效改善混合漿的成膜性和粘附性。 -
Methods of testing plastics - rheological properties - polymer dispersions - determination of white point temperature and minimum film - forming temperature
塑料試驗方法.第7部分:變流性能.方法740c :聚合物懸浮液.白點溫度和最快薄膜形成溫度的測定 -
When apply at high temperature, additional thinning may be necessary to ensure film - forming properties. the film must be even and uniform
在高溫下施工必須額外稀釋，以確保成膜性能。施塗的漆膜必須均勻。 -
And the dopping magneto - optical materials were constructed to better meet the demand for the properties of magneto - optical disk recording media materials, forming the series magneto - optical recording media materials and decreasing the making cost by the method of introducing the light and middling rare - earth into the tbfeco materials. the magneto - optical properties and compositions of the tb - fe - co series dopping magnetic - optical film materials were investigated. the results show that when small amount of adulteration element was introduced into the tb - fe - co, the magneto - optical properties of materials are increased. for example the kerr angle and the coercive force are both improved
對輕、中稀土摻雜的tb - fe - co系列磁光薄膜材料進行丁磁光性能和成分的測試，結果表明：在摻雜元素含量較小時，摻雜后的tb - fe - co磁光材料具有較好的磁光性能， kerr轉角_ k和矯頑力hc都有所改善，摻雜元素的含量應嚴格控制，不能超過一定限度，一般一般摻入量應莊10at左右。
分享友人