finite element program 中文意思是什麼

finite element program 解釋
有限元程序
  • finite : adj. 有限的；【語法】限定的；【數學】有窮的，有盡的。n. 〈the finite〉 有限（性）； 〈集合詞〉有限物。adv. -ly ,-ness n.
  • element : n 1 要素；成分；（構成）部分；分子。2 【化學】元素；【數學】元，素；【機械工程】單元；單體；【無...
  • program : 按遺傳密碼工作
  1. Abstract : for analyzing the residual stress distributing state within the weld joint, and its effect on the performance of welding structure, when welding the ferrite pearlite steel with the austenite steel, this paper develops a finite element program to compute the interface stress of two or over two material. finally, this program is used to analyze the mechanical behavior of heterogenic joint

    文摘:為了分析鐵素體、珠光體類鋼與奧氏體類鋼焊接時，焊接接頭處焊接殘余應力的分佈狀態及其對焊接構件性能的影響，研製了可計算兩種或兩種以上材料界面應力的有限元程序，並用此程序分析了異質接頭的力學行為。
  2. Based on the back - analysis data of some excavation stage, through the non - linear finite element program nef, we can predict the tendency of next excavation stage. the relative error between calculation and measurement is controlled in 25 %, demonstrate the estimate prediction is successful

    根據反演的某一階段的土體參數值，通過非線性有限元程序nfp ，預測后一階段的邊坡變形情況，實例中理論計算值與實測值的相對誤差控制在25 %以內，說明預測是成功的。
  3. Choose two nodes on the edge of the structural to compare the results calculating by the finite element program midas, then we can draw a conclusion that these kinds of space truss systems is sensitive to the libration of the dynamic wind loads. to consider this factor is very necessary in the process of design, we will use the pulsant augmentation coefficient to realize it

    比較靜力風荷載和動力風荷載作用下的有限元軟體的計算結果，選取結構邊緣部分的兩個節點，對比它們在兩種方法計算下的最大位移的計算結果。經過比較可以看出重量輕、頻率低、阻尼小的柔性建築物對風荷載的橫向振動是很敏感的，在進行工程設計時應該考慮這種因素，並可採用乘以風振系數等相應方法來加以體現。
  4. This model helps to make a non - linear finite element program which is tested and verified by the example in umt

    在此基礎上，建立了城市軌道交通橋梁無縫線路縱向力的空間一體化力學模型，編制了非線性有限元模型，通過實例進行了模型驗證。
  5. In the computer simulation, the finite element program ls - dyna was used to simulate six operating modes of experiment

    在計算機模擬方面，利用大型有限元程序ls - dyna對實驗中的六種工況分別進行了數值模擬。
  6. In harbor engineering, reliability has been introduced to the design of foundations based on the limit equilibrium methods. in this paper perturbation stochastic finite element program was compiled to calculate and analysis the reliability of the foundation on muti - layered subsoils

    本文將隨機有限元法引入到地基承載力的計算中，編制了攝動隨機有限元程序，對地基穩定性和可靠度指標分佈情況進行了計算分析。
  7. In this paper, the high - temperature low - cycle fatigue life and fatigue crack propagation life tests are carried on the cylindrical axial symmetry specimens having precrack or non - precrack with different types of notches of 16mnr steel in common use in the petrochemical industry contacting coke drum equipment, the stress / strain and the range of stress / strain of dangerous points are received through stress analysis of the specimens using finite element program under multi - axial stress state. at last, the equations of evaluating the high - temperature low - cycle fatigue life and the fatigue crack propagation life are found through using the least - square regression method

    本文採用無預裂紋和帶預裂紋環狀缺口圓柱形試樣，進行了石化焦炭塔設備常用材料16mnr多維應力狀態下不同缺口形式的高溫低周疲勞總壽命試驗及裂紋擴展壽命試驗，並利用有限元程序對試樣缺口周圍及裂紋尖端附近進行了軸對稱多維應力狀態下的應力、應變場分析，來評價材料不同條件下的高溫低周疲勞總壽命和裂紋擴展壽命，最後利用最小二乘回歸方法，得到了該材料高溫低周疲勞總壽命和裂紋擴展壽命評價方程。
  8. In virtue of finite element program, this paper calculates the model of rc - masonry combination arch bridge in the stages of construction and use in this paper. based on these data, it analyzes the structure behavior of the reinforced concrete arch ribs and the masonry arch ribs using methods of inner force and stress

    本文藉助有限元程序對rc -石砌體組合拱橋的計算模型進行了施工階段和使用階段的計算，並採用應力疊加和內力疊加兩種方法對rc拱肋和石砌體拱板的受力特性進行分析。
  9. Then an thorough computer modeling using finite element program with material, geometry and state triple - nonlinear taken into account is carried out on a series of influencing factors, such as comparison with npn - beam splice connection, comparison of varies designed theories, and the varying of fraction coefficient, diameter, grade, pretension and arrangement of bolts, thickness of web and flanges of beam and column, splicing location, axial loading on column, etc. lots of useful conclusions are drawn form computer modelling. finally, design and construction suggestions are given out. this study fills the black in the field of steel beam - to - column connection with cantilever beam high - strength bolted - splicing at both home and abroad

    然後，本文在考慮材料、幾何和狀態三重非線性的基礎上，對該連接形式進行了全面的計算機模擬，主要考慮了帶懸臂梁段全螺栓拼接的樑柱連接節點與無拼接的樑柱連接及翼緣對接焊接腹板拼接的連接節點的對比，各種設計方法之間的對比，以及翼緣拼接和腹板拼接的螺栓間距、直徑和數量，拼接點與梁端之間的距離，梁和柱的翼緣、腹板厚度，柱的軸力，接觸面的摩擦系數，翼緣和腹板拼接板的厚度等因素的影響。
  10. Based on the work of dr. yang guolin, a finite element program is worked out according to the finite element theory. the data to be imputed can be generated by software super - sap93, which can simplify the work of data preparation

    For以及配套的靜力非線性程序和基頻計算程序，這些程序是以飽和砂土振動理論為基礎，結合我院楊果林博士原有的塑性動力分析程序編制而成。
  11. The construction of the bridge began in oct 1999, and the closing up of the steel tube was in dec 2000. during that period, i learned and analyzed the current construction methods fairly comprehensively, and collected the construction technique data of the cfst arch bridges having been built. based on this, aided by the simulation of construction procedure using finite element program, i proposed the operation program to make the steel tube segment be located at one time, and the scheme of dividing rooms to segment pouring

    大橋於99年10月開工， 2000年12月主橋鋼管合龍，在此期間，本人就目前鋼管混凝土拱橋的施工方法進行了較全面的了解和分析，搜集了此類已建橋梁的施工技術資料，在此基礎上，又藉助有限元程序對施工過程模擬計算的支持，提出了在梅溪河大橋懸臂安裝過程中，鋼管節段一次就位的操作程序和鋼管混凝土分倉灌築的方案，並為施工單位采納應用。
  12. Thirdly writer, using linear elastic theory and finite element program ( ansys ), analyzed expanding bolt pullout test. fifthly, writer using the modified mohr - coulomb failure theory, on the base of curving failure surface, derived a theoretical formula between pullout force and compressive strength. then the thesis compared the formula with the strength - detecting formula of expanding bolt pullout method

    本文採用ansys有限元程序對脹栓拔出法試驗過程進行彈性理論分析；以修正的摩爾-庫侖破壞準則，在擬合實際破壞面的基礎上推導出極限狀態下脹栓拔出法的混凝土拔出力與混凝土抗壓強度的理論公式，並把該公式與脹栓拔出法測強公式進行了比較。
  13. A two - dimensional finite element program, in digital visual fortran version 6. 0 language, is developed for the numerical computation. due to time limit, elastic modeling is adopted while writing program

    在此基礎上用digitalvisualfortran語言編制了相應的二維彈性有限單元程序，並通過算題論證了程序的準確性。
  14. The same type of cement - soil mixing pile with concrete core, concrete pile and cement - soil pile that means they have the same pile length and pile diameter is deeply analyzed by finite element program. we get the q - s curve, the axis force of pile body curve, the stress of pile curve and the side and the end sharing load ratio of the pile curve by finite element program. with the help of the finite element program, the paper finds the relations between the pile ' s parameter and its bearing capacity and load transferring properties

    利用有限元計算分析了同比（樁長相同、樁徑相同）水泥土組合樁、水泥土攪拌樁和混凝土鉆孔灌注樁，得到了它們的荷載沉降曲線、樁身應力曲線、樁身軸力曲線、樁側樁端分擔荷載曲線等，通過這些曲線對它們的荷載傳遞規律以及變形特性進行了深入的分析。
  15. Fourthly, with the finite element program, the author analyzes the relationship between the load magnitude or frequency and range of breakage or pore pressure. this can provide appropriate parameters for the method of vibrating grouting. fifthly, adopting the compressible porous medium, the author adduced dynamic theory of liquid saturated porous medium to analyze the displacement and force in the sand when there is dynamic load below the earth surface

    基於連續介質力學的混合物理論建立的多孔介質理論和動力控制方程，假設砂土滿足各向同性並處于彈性小應變狀態，豎向振動力將在飽和砂土內部產生三種波，分析了這些波的彌散曲線和特徵衰減曲線，從波傳播的角度，研究了振動力參數和土性參數對振動范圍的影響。
  16. This paper applies nonlinear finite element program bsnfem to analyze the behaviors of eccentrically braced steel frames under cyclic load. the study that comprehensive and systematic analyze the factor of links length, thickness of links flange, distance of links rib, thickness of links rib and angle of brace to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel frames have been some studied before. this paper fills the black in the filed factor of high - span ratio, brace stiffness and brace - to - beam connections to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel trames and any factor to be changed affect energy - dissipation capacity of y shape eccentrically braced steel frames

    對耗能梁段的長度、耗能梁段腹板的厚度、耗能梁段翼緣的厚度、耗能梁段加勁肋的間距、耗能梁段加勁肋的厚度、支撐的夾角等因素的改變對d形、 k形偏心支撐鋼框架耗能的影響，前人已有一些研究，本文對這些因素的影響進行了全面系統的分析，完善了理論分析的不足；而結構高跨比、支撐剛度、支撐與梁的連接形式等因素對d形、 k形偏心支撐鋼框架破壞機理的研究以及各種因素對y形偏心支撐鋼框架破壞機理的影響，則很少有人涉及，本文對此也進行了深入系統的分析，填補了這一研究空白。
  17. The reduction factors derived from curve fitting based on calculation results by the finite element program ( ansys ) considering all kinds of damages such as cutouts, corrosion, cracks, denting, initial deflection and residual stress are introduced to modify the effective width of perfect panel in the present paper

    本文考慮板中可能存在孔洞、腐蝕、裂縫、局部撞損和初始焊接變形或殘余應力等損傷和初始缺陷，對不同的損傷形式用有限元程序（ ansys ）進行大量的計算，通過曲線擬合的方法引入折減系數對完好板格的有效寬度進行修正。
  18. According to the results of the tests and finite element program, the paper put forward the structure need of the cement - soil mixing pile with concrete core, gives the calculating formula of pile ' s bearing capacity

    根據室內外試驗和有限元分析的結果，提出水泥土組合樁的構造要求和水泥土組合樁豎向承載力計算公式。
  19. The comparative analysis is made firstly, which shows that the truss arch aqueduct can be built on the weak foundation and is also satisfied with the demand for large span length and the great discharge ability, so the type of aqueduct is a better for the project. then the finite element program ( super sap93 ) is applied to the structural analysis of the space structure

    首先通過對常用渡槽結構型式的對比分析，闡明該渡槽是一種可在軟弱地基上修建的、能滿足大跨度、大流量要求、適用於南水北調中線工程的排水建築物，然後運用有限元分析程序supersap93對桁架拱空間結構進行了受力分析。
  20. On addition, the author research on optimizing the solver of the finite element program

    另一方面，作者對優化有限元計算求解器也進行了初步的探索。
分享友人
分享到 Line

分享到臉書