flow chart of time control 中文意思是什麼

flow chart of time control 解釋
時間控制流程圖
  • flow : vi 1 流,流動。2 (血液等)流通,循環。3 流過;川流不息;(時間)飛逝;(言語等)流暢。4 (衣服、...
  • chart : n 1 海圖,航(線)圖,航海圖;地勢圖(=physical chart),(軍用)地形圖(=topographic chart)。...
  • of : OF =Old French 古法語。
  • time : n 1 時,時間,時日,歲月。2 時候,時刻;期間;時節,季節;〈常pl 〉時期,年代,時代; 〈the time ...
  • control : n 1 支配,管理,管制,統制,控制;監督。2 抑制(力);壓制,節制,拘束;【農業】防治。3 檢查;核...
  1. This disquisition aimed at plc reactive dispatch curve controller, associating the entire exploiting process, expounded in guiding ideology, control standard, function and structure design, software system design, analog experiment, fixing and debugging and so on, also part of flow schematic diagram ( the ladder chart was n ' t drawn because of too many network and length limit ). this design involves many subject such as power systenu automatic control microcomputer control and electroa during the design, we have read a great deal of concerned data, base on the sufficient investigation analysis and research, associating the practicality of huanren power plant, we introduced and exploited plc reactive dispatch curve controller in the first time

    本文針對plc無功調度曲線控制器,結合整個研製過程,在設計指導思想、控制準則、性能設計、裝置構成設計、軟體系統設計等方面進行了闡述,並給出了部分程序流程簡圖(由於梯形圖網路數太多,受篇幅限制沒有給出) 。本設計涉及到電力系統、自動控制、微機控制、電子等多學科知識,在設計過程中,我們查閱了大量相關的資料,在充分調查、分析、研究的基礎上,結合桓仁發電廠實際情況,首次提出並研製出了plc無功調度曲線控制器。
  2. The hardware circuit design include : industrial control computer configuration, selection of industrial control board type, design of the power supply and monitoring interface circuit, design of signal processing interface circuit ( the constant current source circuit, the time base signal processing circuit, the processing circuit for the signal to be measured ), design of panel control circuit, design of the system self - checking circuit, and etc. the program flow hart include : main program flow chart, system boot - strap self - checking program flow chart, manual static testing program flow chart, semiautomatic static testing program flow chart, automatic static testing program flow chart, dynamic testing program flow chart, transient testing program flow chart, source voltage and current monitor program flow chart, investigate function testing program flow chart, and etc. the measure system offers six working power supplies, the signal of time base, the signal of constant current source, sine wave signal and step to leap signal, and measures the frequency of the output pulse signal of the wide range pulse convert circuit accurately under three kinds of different test state ( static form, dynamic form and transient form )

    硬體電路設計包括:工控機配置、工控板卡選型、產品電源及監控介面電路設計、信號處理介面電路(恆流源電路、時基信號處理電路、被測信號處理電路)設計、面板控制電路設計、系統自檢電路設計等。程序流程圖包括:主程序流程圖、系統開機自檢程序流程圖、手動靜態測試程序流程圖、半自動靜態測試程序流程圖、自動靜態測試程序流程圖、動態測試程序流程圖、暫態測試程序流程圖、電源電壓和電流監控程序流程圖、研究功能測試程序流程圖等。測試系統提供六路工作電源、時基信號、恆流源信號、正弦波信號和階躍信號,並對三種不同測試狀態(靜態、動態、暫態)下大量程脈沖變換電路輸出脈沖信號的頻率進行精確測量。
  3. Three - phase full bridge controlled rectifier, filter circuit and the common loads " mathematics models are built and analyzed. according to the rate of the transition process, the controlled rectification power supply can be classified into fast response and slow response. based on identification of the transition processes using the slope method, the different fuzzy control strategy is adopted. the control method can meet the requirements of real time control and non - error regulation. the simulation results verify its practibility. after that. the design scheme based on dsp is introduced including the design of hardware and software flow chart. emc is an important aspect which can not neglected, so the designs of emc are summarized including hardware and software

    根據過渡過程的快慢將可控整流電源系統分為快響應過程和慢響應過程,本文在利用響應曲線斜率法辨以過渡過程的基礎上,分別針對快響應過程和慢響應過程採取了相應的模糊控制策略,以滿足快響應過程要求實時控制,快速跟蹤誤差變化,慢響應過程要求精確定位,無差調節的要求,模擬結果驗證了該方法的有效性,進而分析了用dsp實現該調節器的硬體電路和軟體流程的設計思路。
  4. As a result, it is no need for the endpoints to maintenance any system control task. in this article we propose a compactness coupling conference system architecture, and at the same time we analysis the system key techniques, giving a part of flow chart and pseudocode as examples. main content are given as below : how to use direcshow technique to obtain multimedia data ; multimedia data transport over ip network ; multicast principal and application in the system ; packing and unpacking rtp / rtcp packet so as to control network flow and in this part we introduce spillage arithmetic ; as the core part of the system, conference control and management are the main concern in our design

    323框架基礎上提出緊耦合式會議系統體系結構,並以c s結構作為實現模型;本文對會議系統的中心mcu流程進行分析設計,並建立數據結構;該部分還涉及到對各個資源的調度;為了對會議控制有更好的理解,用petri網描述了會議控制會議管理的過程並提出了靈活的授權管理機制;對服務器端的數據通信設計了多播通信的實現方案;本文簡單回顧了directshow技術的應用,並在此基礎上實現了多媒體數據的採集和回放;為實現多媒體在網路上實時傳輸選擇不可靠傳輸協議udp ,為使數據能正確回放,採用了rtp和rtcp協議。
分享友人