fluid flow angle 中文意思是什麼
fluid flow angle
解釋
液流角-
Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。 -
In this way, when obturation cubage leave absorb oil cavity it connects the eduction oil cavity with the v trough and with the increasing of the turning angle, the size of the cross section of v trough become bigger and bigger, which make the pressure between the cavity of two blades much higher and higher, and until it completely connects the eduction oil cavity, it reaches the pressure of the eduction, and it can effectively reduces the fluid noise caused by high pressure return flow
這樣，當密閉容積離開吸油窗口之後，通過v型尖槽逐漸與排油窗口連通，隨著轉角的增加， v型尖槽通流截面積逐漸增大，這就使兩葉片間容腔內的壓力逐漸升高，直至完全接通排油窗口時，才升壓達到壓油腔的壓力，這樣可以有效地降低因高壓迴流而引起的流體噪聲。 -
Detailed predictions on the fluid flow in mold and in cavity of nozzle working end were obtained at different side - hole angle and submerged depth of nozzles, and then the flux variation of liquid steel passing through central hole of the three - hole nozzle and the fluctuation of liquid steel in mold were inspected based on above predictions
針對3孔浸入式水口不同側孔傾角和浸入深度，數值模擬對結晶器內鋼水流動做出了較為詳細的預報，研究工作就此分別考察了水口中心孔流量變化和鋼水液面波動幅度。 -
The characteristic of combined heat and mass transfer by natural convection has been the focus of researches for a long time. numerical analysis is conducted for combined heat transfer and mass transfer by natural convection on inclined surface. effects of the inclination angle and the ratio of buoyancies due to heat diffusion and mass diffusion on fluid flow and heat and mass transfer characteristics have been investigated for pr = 0. 7 and sc = 0. 05 - 5. 0
本文採用數值計算方法研究了傾斜平面上的傳熱傳質復合自然對流，求解了動量、能量及質量的完整方程，考察了熱質擴散共存時傾斜平面上的流動和傳熱特性，著重分析了熱浮力及物質擴散浮力之比b和傾斜角度對流體流動和傳熱傳質特性的影響。 -
Finally, the two dimensional flow in the diffuser is calculated, the results show that the change of ma makes an effect to the performance of the diffuser. owing to the accretion of ma, the action of oblique shock waves and the boundary layer pricks up, the flow separates from the wall where the shock waves impinge on the boundary layer more quickly, the cluster of diamond shock waves becomes larger. moreover, by comparing the change of flow field under different structure parameter, it is found that the augment of length of constant area section alter the structure of fluid field little, a smaller area ratio and larger angle of compression section make the diffuser working better
最後，針對擴壓器中的二維流場進行了數值模擬，結果表明馬赫數對擴壓器性能影響較大，隨著馬赫數的增大，擴壓器管道內激波-附面層干擾加劇，流動從附面層分離相應加劇，激波串數目增多;通過比較不同結構參數下的擴壓器內流場，發現等直段長度的變化幾乎沒有改變流場結構，只是對局部流場稍有影響，並且在其它參數不變的情況下，一定范圍內減小面積比a2 / a1和增大收縮角有利於擴壓器性能的提高。 -
In general, spiral flows in pipes are generated by several means : fixing revolving - flow implement, guiding fluid by vanes with a certain angle, tangentially ejecting, and axially rotating pipe
目前螺旋流的產生方法主要有：安裝旋流器、安裝導流片、切向噴射等，這些不在本文的研究范圍內。
分享友人