full size design 中文意思是什麼

full size design 解釋
足尺設計圖
  • full : adj 1 充滿的，裝滿的。2 充分的，豐富的；擠滿的；（吃、喝等）盡興的，3 （精神）飽滿的。4 完全的，...
  • size : n 1 大小，尺寸規模身材。2 （鞋帽等的）尺碼，號；（紙張的）開。3 巨大，大量；相當大的分量。4 〈口...
  • design : vt 1 計劃，企圖，立意要…。2 指定，預定；留給，留著。3 設計，草擬，擬定，籌劃；起草，畫草圖，打（...
  1. On the premise of a given set of material parameter, structural boundary shape and condition, design variables - thickness of plate and shell, is designed to minimize the structural weight subjected to the constraint conditions. 1. for the problem with size and stress constraints, full stress design method is used to solve the sectional optimization of plate and shell structures

    在給定了板殼的材料常數、板殼結構的邊界形狀和邊界條件的前提下，確定表徵板殼厚度的設計變量，在滿足約束條件下實現結構重量最小： 1 .對于尺寸和應力約束的問題，使用滿應力方法求解。
  2. For confirming the results, a full - size model ( dj / dj = 0. 6, t / t = 1. 5 ) was analyzed by means of strain gauge test. the reliability of finite element analysis was proved because the results basically accorded with that of the test. secondly, in this paper, in order to carry out a fair assessment of the reinforcement design on spherical shell with transnormal nozzle, a comparison of reinforcement method was done between jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a4 and hg20582 - 1998 specification for stress calculation of steel chemical vessels

    為了驗證ansys分析結果的可靠性，對其中一組參數下（開孔率0 . 6 、厚度比1 . 5 ）的模型容器，採用電測法進行了應力測試，並將得到的實驗結果與有限元結果進行了比較，二者在應力分佈狀況和大小上均基本吻合，證明此種結構運用ansys進行分析，其結果是完全可靠的。
  3. The actual design ordinarily adopts the full - size experimentation means, which has the advantages that can reflect the real resistance, but its " shortage is also obviously : complex, uneconomic and mess around

    這種設計方法的優點是可以比較真實的反映結構的承載力，缺點是太麻煩，每次都要做試驗，不但費時費力，而且也不經濟。
  4. Through the frontal impact test of full size minibus and computer simulation analysis, a parameterized model is set up for the design of body structure crashworthiness in frontal impact during concept design phase, with the modeling techniques well expounded

    摘要選取某微型客車為研究對象，通過實車正面碰撞試驗和計算機模擬分析，建立了用於概念設計階段的面向微型客車車身結構正面抗撞性設計的參數化模型，闡述了建立模型的建模技術。
  5. Abstract : based on sun workstation sparc20 ug software has been used in cad of full - mold casting tool of cylinder head of model n485q multi - cylinder diesel to solve knotty problems such as cut of pattern membrane of cylinder head. visibility of size of each part of cooperation of tools with mold cavity and, molding of complex curved surface. tool design thinking of full - mold casting of complex diesel castings has been explored

    文摘:採用基於5un工作站sparc20的ug軟體進行n485q多缸柴油機氣缸蓋實型鑄造模具的計算機輔助設計，解決了缸蓋模樣的模片切取、模具配合型腔各部位尺寸的可視化以及復雜曲面的造型等疑難問題，探索出了一條復雜內燃機鑄件實型鑄造的模具設計思路。
分享友人
分享到 Line

分享到臉書