furnace burner 中文意思是什麼

furnace burner 解釋
爐子燒嘴
  • furnace : n. 1. 爐子；熔爐；高爐。2. 極熱的地方。3. 磨煉；艱難。vt. 在爐中燒熱（金屬）。
  • burner : n. 1. 燒…人；氣焊工，氣割工。2. 燃燒物；爐子；燈；燈頭，燈口；噴燒器，噴燈；噴嘴；燃燒室。3. 火藥柱。
  1. This thesis establishes the main factor of heating surface slagging of no. 1 boiler, that it is due to irrational layout of furnace heating surface, improper angle of burner which lead to flames attaching to furnace walls. such deduction is built on the basis of necessity of analyzing the heating surface slagging, the type of coal, the design of the furnace and burner, the operational condition and other factors effecting slagging of boiler. the research is mingled with practical operations of no. 1 boiler in inner mongolia fengtai electric power generation co, ltd

    本論文從分析燃煤鍋爐結渣問題必要性出發，從煤種、爐膛及燃燒器設計、運行工況等因素對鍋爐結渣的影響著手，結合內蒙古豐泰發電有限公司~ # 1鍋爐實際運行中存在的問題，確定了~ # 1爐受熱而結渣的主要原因是爐膛受熱面布置不合理，燃燒器角度不合適導致火焰貼壁所致。
  2. According to fuel and and operation condition in chongqing iron and steel group corporation, many kinds of advanced technologies are adopted, such as closed loop soft water circulation cooling, copper cooling stave, bell - less top with central charging hopper, carbon bricks combined furnace bottom with ceramic cup, russia top burner type hot air stove, duplex preheating of hot air stove, and nut coke charging

    摘要根據重鋼高爐的原燃料條件和操作條件，設計了重鋼四高爐擴容性易地大修工程，採用了全軟水密閉循環冷卻、銅冷卻壁、串罐式無料鐘爐頂、炭磚陶瓷杯復合爐缸、俄羅斯「卡魯金」頂燃式熱風爐、熱風爐雙預熱、焦丁入爐等先進技術。
  3. The reform scheme of no. 1 boiler in fengtai company is confirmed on the basis of cold / hot tests, theoretical discussions and calculations. in the process of field retrofit, it is indicated in the operation of the improved furnace that without the change of furnace structure, the transform of the burner angle has shrunk the tangential diameter and prevented flames burning on furnace walls, and the burning state of furnace has been bettered, simultaneously, lowering the slagging wi in furnace, thus laying sol id foundation for the safe and economic operation of generating units. wuyanrong ( power plant thermal power engineering ) directed by prof

    本論文通過冷、熱態試驗，經過論證和計算，確定了豐泰公司~ # 1爐燃燒器的改造方案，並進行了現場改造，改造后實際運行狀況表明：在無法改變爐膛結構的情況下，改變燃燒器角度，縮小切圓直徑，使火焰不貼壁，改善了爐內燃燒工況，同時降低了鍋爐結渣的程度，為機組的安全經濟運行奠定了必要的技術基礎。
  4. Design research on using gjh mixing burner to burn coke oven gas which is mixed with blast furnace gas in lime rotary kiln

    混合燃燒器在石灰回轉窯上摻燒高爐煤氣的設計研究
  5. Using the furnace itself to dry the refractory has been reported in some cases but usually the flue gases will be too hot even with the minimum burner tip combination

    有過報道，說有時用加熱爐自身來乾燥耐火磚，但通常煙氣會太熱（即使燒嘴火嘴組合最小） 。
  6. Research on numerical test for solving slagging problem in furnace by using coal powder burner with guide - plate

    導流板式煤粉燃燒器解決爐內結渣的數值試驗
  7. Application of gjh mix burner with burning coke oven gas and blast furnace gas in lime rotary kiln

    低熱值高爐煤氣與煤粉混燒技術的探討
  8. Burner control furnace control

    鍋爐控制產品
  9. The fuel burner of an open - hearth furnace is water - cooled, as is the valve that regulates the flow of air and waste gases

    平爐的燃料燃燒室是用水冷卻的，控制空氣和廢氣的閥也是水冷的。
  10. Production test of the production line is showed that anneal furnace combustion system with regenerative radiant - tube combustor compare with conventional radiant tube burner not only have superiorities on saving energy and environmental protection but also have advantages on temperature distribution and temperature control properties

    生產線試生產的情況表明，退火爐燃燒系統使用蓄熱式輻射管燃燒器比使用常規輻射管燃燒器不僅在節能、環保方面具有優勢，而且在加熱均勻性和爐溫控制方面也有一定優越性。
  11. A combustion model has been built and burning process has been simulated by computer in blast furnace stove with ceramic grid - burner

    摘要建立了高爐熱風爐燃燒數學模型，應用計算機模擬研究方法對中空柵格陶瓷燃燒器的火焰形態進行了模擬研究。
  12. Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  13. The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  14. The new type regenerative burner can be used alone and installing easy. using the regenerative burner, htac can be realization in the forge heating furnace and the effect is satisfied

    摘要介紹新型「自身」蓄熱燒嘴，單個使用，安裝方便，在鍛造爐上實現了高溫空氣燃燒，提高了加熱質量，降低了燃料消耗，取得了滿意的效果。
  15. When applying the burner to the boiler, it is necessary to correctly position the flange so that the burner head enters the furnace to the extent specified by the boiler manufacture

    當燃燒器裝在鍋爐上時，需要正確定位法蘭，使燃燒頭按鍋爐製造商指定的長度進入爐膛。
  16. The furnace for the test is the oil - burner that is designed and produced by ourselves. the whole test process is undertaken in the modeled standard temperature curve. the result of the test demonstrates that the properties of the furnace are stable and convenient for use

    火災試驗使用的試驗爐為自行研製的燃油火災試驗爐，全部的試驗是在模擬標準升溫曲線的基礎上進行的，試驗結果表明爐子性能穩定、使用方便。
  17. Main products of the company include coal - water fluid boiler, coal - water fluid / oil / gas burner, steam boiler, hot water boiler, vacuum hot water boiler, heat carrier furnace, fluid handling equipment, reaction pot, fermentation tank, heat exchanger, grade br1 pressure vessel and boiler auxiliary equipment and accessories, etc

    主要產品有:水煤漿專用鍋爐、水煤漿/油/氣燃燒器、蒸汽鍋爐、熱水鍋爐、真空熱水鍋爐、熱載體爐、流體裝卸設備、反應釜、發酵罐、熱交換器、 br級壓力容器，鍋爐輔機及配件等。
  18. Based on the summary of the development of digital furnace and characteristics of regenerative burner, the paper introduce the digital reheating furnace with regenerative burner which is first new furnace built by stein - heurtey company for shijiazhuang iron & steel company ltd., and expatiate the system configuration of this furnace and its ' advantage

    摘要在概述數字化加熱爐發展及蓄熱式燒嘴特點的基礎上，簡要介紹了斯坦因公司為石家莊鋼鐵股份有限公司建立的第一座數字化單蓄熱步進梁式加熱爐，並著重說明?此座加熱爐系統組成及其應用優勢。
  19. Multi burner and heating furnace control system

    多燃燒器與加熱爐控制系統
  20. Study and design of structure optimization in regenerative burner of reheating furnace

    加熱爐蓄熱燒嘴結構優化研究與設計
分享友人
分享到 Line

分享到臉書