gas delivery pressure 中文意思是什麼

gas delivery pressure 解釋
交氣壓力
  • gas : n （pl gases ）1 氣，氣體，氣態 〈cf fluid; solid〉 2 可燃氣，煤氣，沼氣；【礦物】瓦斯。3 【軍事...
  • delivery : n. 1. 引渡，交付；【商業】交貨；【法律】正式讓渡。2. 運送；投遞；傳送。3. 分娩。4. 陳述，講演；口才。5. 【棒球】投球。6. 救助；釋放。
  • pressure : n 1 壓；按；擠；榨。2 【物理學】壓力，壓強；大氣壓力；電壓。3 精神壓力，政治[經濟、輿論等]壓力。4...
  1. Then the paper also study the atomizer structure ( the protrusion of the delivery tube value h ), atomizing gas pressure p, over - heat temperature of alloy a t, the component of solder alloy and atomizing medium and so on

    進一步對霧化器結構（導液管突出高度h ） 、霧化氣體壓力p 、合金過熱度t 、焊錫合金成份和霧化介質進行了研究。
  2. Combining physical experiments and theoretical analysis, this literature has performed thorough research on gas properties of delivery pipeline system, pressure current rush to interception air - mass in pressure pipeline, water hammer with gas that happens with gas releasing and liquid column separating

    本論文通過物理試驗與理論分析對輸水管道系統中的氣體特性、壓力水流沖擊截留氣團和包含氣體釋放和液柱分離現象的含氣水錘進行了深入研究。
  3. The conclusions are drawn as following : 1. regularity of fabrication in aluminum matrix composite ring - shaped performs with large dimensions and effects of parameters were investigated, based on the novel crucible movable spray deposition technology and equipment. the optimal parameters are that the diameter of the delivery tube is 3. 8mm, spray gas pressure is 0. 8mpa, spray height is 200mm, and transferring pressure of sic is 0. 5mpa

    通過系統的實驗研究得到如下結論: 1 .基於新型的移動坩堝自動化控制噴射沉積環坯制備技術及裝置，研究了大尺寸鋁基復合材料環坯的制備規律，討論了噴射沉積工藝參數對沉積坯形成過程的影響，得到了最佳工藝參數:導流管直徑d = 3 . 8mm ，霧化氣體壓力p = 0 . 8mpa ，噴射高度h = 200mm ， sic顆粒輸送壓力p送= 0 . 5mpa 。
  4. Medenus gas - druckregeltechnik inh. dieter medenus - the delivery program covers regulator, gas industry and pressure regulators as well as gas pressure rule and gas production

    是一家高水平的公司，該公司為您供應高質量的產品並從事燃料，氣體產生、氣體生產的製造和銷售。
  5. The optimal parameters of making high silicon content aluminum alloys is : spray height is 220 - 230mm, spray angle is 30 ? the scanning velocity of atomizer is 30mm / s, the original offset of the substrate is 30mm, rotation velocity of the substrate is 120rpm, spray gas pressure is l. ompa, the diameter of the delivery tube is 3. 6mm, the drawing velocity of the substrate will be adjusted on - line with a plc on the basis of the spray

    通過對多層噴射沉積原理及工藝參數的研究，得出制備al - 22si - 3cu - 1mg合金的最佳工藝參數為：噴射高度為220mm - 230mm ，基底轉速為120rpm ，霧化器掃描速度為30mm / s ，基底下降轉速依據噴射情況由智能控制器進行實時調整，噴射角度為30 ，初始偏心距為30mm ，導流管直徑為3 . 6mm ，霧化氣壓為1 . 0mpa 。
分享友人
分享到 Line

分享到臉書