gear change 中文意思是什麼

gear change 解釋
變速齒輪
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  • change : vt 1 改變，變更，變換，變革。2 交換；兌換；把（大票等）換成零錢；把（支票等）兌成現金。3 換（車、...
  1. Bevel wheel change gear

    傘齒輪變速裝置
  2. How do you tell when to change gear ?

    你怎麼確定何時換擋？
  3. You should change gear -- the engine 's starting to labor.

    你該換擋了發動機有些吃不住勁了。
  4. You should change gear the engine ' s starting to labour

    你該換擋了- -發動機有些吃不住勁了
  5. Change gear lever

    變速齒輪桿
  6. You can change into a higher gear now you are going faster.

    你既然已加快了速度，就可以換上高擋了。
  7. Regulation and measurement of noise on board with diesel engines, change to high gear

    掛槳機船噪聲限值及測量方法
  8. You will need to change into a lower gear when going up this hill.

    上這座山時你需要換低擋。
  9. Electrical signals are sent to the hydraulic valves by the microcomputer when a gear change is required by the powertrain control strategy.

    當按照動力裝置控制方案要求換擋時，電信號由微計算機送到液壓閥。
  10. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  11. Firstly the dissertation analyses the reason of vibration and noise of the transmission gear and the box, drawing a conclusion that the change of gear mesh rigidity and transmission error are the crucial causation to engender vibration and noise of the gear - box ; the main source of the noise is the syntonic noise in box vibration and noise

    本文首先分別分析了變速箱傳動齒輪和變速箱箱體的振動噪聲產生機理，得知產生變速箱傳動齒輪振動噪聲的主要因素是輪齒嚙合剛度的變化和傳動誤差的影響;且在變速箱箱體振動噪聲中自鳴噪聲是汽車變速箱的主要噪聲源。
  12. Change gear box

    交換齒輪箱
  13. Change gear bracket

    交換齒輪架
  14. The combine harvester is overall 3 packets of period of efficacy are 1 year ; 3 packets of period of efficacy are main part 2 years, main part is to point to internal - combustion engine airframe, cylinder housing of casing of lid, flywheel, frame, gear - box, clutch, change gear case of machine, final drive to body

    聯合收割機整機三包有效期為1年；主要部件三包有效期為2年，主要部件是指內燃機機體、汽缸蓋、飛輪、機架、變速箱箱體、離合器殼體、轉向機、最終傳動齒輪箱體。
  15. The heat expansion coefficient of plastic is much higher than metal caused by abrasion heat and the change of environment condition. plastic gear needs enough gap

    因磨擦熱和環境條件的變化，塑料比金屬熱膨脹系數高許多，塑料輪需要足夠的
  16. Adaptable units of wire and cable machinery lapper. part 5 : speed change able gear box for lapping

    電纜設備通用部件.繞包裝置.第5部分:繞包變速箱
  17. I have never driven an automatic car before and i keep trying to change gear, but i expect i ' ll soon get the hang of it

    我以前從沒駕駛過自動汽車，因此我不停地變換排擋，但我想我會很快掌握它的竅門的。
  18. Measuring engine transient process data in ca1258p1k2l11t1 truck in accelerated mode, recording and analyzing the data, then analysis the test error. 4. building model and simulating two typical running mode ? fixed 6th gear acceleration with initial vehicle speed 40km / h and gear change acceleration starting with 2nd gear, comparing calculated result with test result, revising transient process simulation model and analyzing error between calculation

    本文基於ca1258p1k2l11t1載重卡車對ca6df2 - 26發動機的瞬變工況進行試驗和模擬計算，結果表明: 1 ） gt - power軟體可以很好的模擬、分析、預測發動機瞬變過程，模擬計算的結果與試驗結果很接近，試驗證明，預測分析指出的改進方向是正確的; 2 ）加裝電動增壓器可以降低整車使用油耗，改善低速煙度排放，縮短加速時間，改善整車的加速響應; 3 ） gt - power軟體預測分析配合發動機和整車試驗是分析、解決發動機瞬變過程的有力工具。
  19. 2. gear change feeding device equipped with precision indexing samensures an accuracy of 0. 05mm at the feeding speed of 60

    由極精密之indexing cam所組成之gear change式送料
  20. In this paper, the optimum technique and reliability design are connected together to bring up the method of reliability and optimization design of the gear change mechanism

    =本文將現代設計方法中的優化技術與可靠性設計理論相結合，提出了鉆機關鍵零件的可靠性優化設計方法。
分享友人
分享到 Line

分享到臉書