gear transmission error 中文意思是什麼

gear transmission error 解釋
齒輪傳動誤差
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  • transmission : n 遞送；傳遞；傳達；傳染；移轉；【機械工程】傳動；傳遞；變速器；聯動機件；【無線電】傳送；發射；...
  • error : n. 1. 錯誤；失錯。2. 謬見，誤想；誤信；誤解。3. 罪過。4. 【數學】誤差；【法律】誤審，違法；（棒球中的）錯打。adj. -less 無錯誤的，正確的。
  1. In this paper, error sources and the relation between error source and transmission error of harmonic gear drive are deeply analyzed based on its working principle and structure. then synthesize these errors by using stochastic error theory to write out estimative formula that calculate transmission error

    本文重點對諧波齒輪傳動的運動精度進行分析研究，從諧波齒輪傳動運動誤差的產生入手，首先對誤差源進行了深入分析，然後對運動誤差進行了分析和綜合。
  2. Firstly the dissertation analyses the reason of vibration and noise of the transmission gear and the box, drawing a conclusion that the change of gear mesh rigidity and transmission error are the crucial causation to engender vibration and noise of the gear - box ; the main source of the noise is the syntonic noise in box vibration and noise

    本文首先分別分析了變速箱傳動齒輪和變速箱箱體的振動噪聲產生機理，得知產生變速箱傳動齒輪振動噪聲的主要因素是輪齒嚙合剛度的變化和傳動誤差的影響;且在變速箱箱體振動噪聲中自鳴噪聲是汽車變速箱的主要噪聲源。
  3. Take the reduction of transmission error of gear and the fluctuation magnitude of meshing rigidity as the judging criterion and at the same time ensuring the variation of loading to be a smooth transition

    以減小齒輪傳動誤差和嚙合剛度的波動大小為衡量標準，同時確保載荷變化呈平穩過渡。
  4. 5. software designing about planetary - gear transmission. it consists of calculation of equivalent error of the averaged load component, force and deformation analysis of component, contact stress and bending strength analysis. 6

    用vb6 . 0自行開發了行星變速箱計算機輔助分析程序設計，該分析程序主要功能包括均載件的等效誤差、各部件的受力及變形分析及齒輪彎曲強度及接觸強度校核6
  5. 1. each kind of averaged load unit of planetary - gear transmission is described in this paper. equivalent error of the averaged load component of four - planet - gear transmission is analyzed for first time as well as the affection of the manufacturing error of elementary component to the displacement of the averaged load component

    本文的主要研究工作有： 1 .對各種類型的均載機構進行了比較；首次分析了4行星輪機構的均載構件等效誤差，分析了安裝和製造誤差及其對均載構件均載位移量的影響。
  6. The harmonic drive and planetary gear transmission were carried on as examples for comparison, which lead to the results that the driving error of harmonic drive is greater than that of planetary gear transmission and the hysterisis error is smaller than the latter

    在此基礎上，對諧波齒輪傳動裝置與行星齒輪傳動裝置進行實例對比分析，指出在閉環伺服系統中，諧波齒輪傳動裝置比行星齒輪傳動裝置的回程誤差小，但諧波齒輪傳動裝置的傳動誤差對系統的影響大於行星齒輪傳動裝置。
  7. It is well known that the gear contact ratio has a close relation with the gears transmission error, contact pattern, load distribution, influences the gears meshing smooth, noise, dynamic strength and stiffness. based on development of the meshing theory, using tca, ltca and experiments, spiral bevel gears with high contact ratio are researched systematically

    眾所周知，齒輪的重合度與齒輪傳動誤差、接觸印痕與載荷分配密切相關，進而影響到齒輪嚙合的平穩性、噪聲、動剛度與動強度等。
  8. ( 2 ) calculation formula of the transmission error and return difference have been derived and measures to reduce them have been proposed. ( 3 ) software about design and analysis of precision gear installation has been developed

    （ 2 ）推導了齒輪傳動誤差和傳動回差計算公式，以此為依據歸納出減小傳動誤差和傳動回差應採取的結構措施，以提高整個裝置的傳動精度。
分享友人
分享到 Line

分享到臉書