gel time 中文意思是什麼

gel time 解釋
膠化時間
  • gel : n. 凍膠，凝膠（體）；定型發膠。vi. （-ll-） 成凍膠，膠化。
  • time : n 1 時，時間，時日，歲月。2 時候，時刻；期間；時節，季節；〈常pl 〉時期，年代，時代； 〈the time ...
  1. 08. 02 test method for gel time and peak exothermic temperature of reacting thermosetting resins

    活性熱固樹脂膠凝時間和最大放熱溫度測試方法
  2. 3. based on the gel time and dsc curve figure of two kinds of modified phenolic resin and flory and kissinger theory, the rage of cure process parameters for the resin system, moulding pressure and resin content are established

    3 、通過對二種改性酚醛樹脂體系凝膠時間、 dsc曲線圖的分析，引入flory理論、 kissinger理論，確定了樹脂體系的固化工藝參數（固化溫度、固化時間、后處理溫度）范圍；並初步確定了成型壓力和樹脂含量的范圍。
  3. In comparison with sol - gel system catalyzed by potassium carbonate and sodium carbonate, the gel time was markedly shortened and the densities of the prepared carbon aerogels were obviously reduced

    相對以k _ 2co _ 3和na _ 2co _ 3為催化劑的凝膠體系，凝膠化時間大大縮短，所得氣凝膠密度降低。
  4. In this paper, studying on the polymerization reaction in silicic acid solution is determined and the gel time of polysilicic acid is obtained when acetic acid compound exist

    摘要在前人研究工作的基礎上，應用乙酸進行硅酸聚合膠凝的實驗研究，實驗結果表明，當硅酸溶液中有乙酸化合物時，硅酸聚合膠凝的時間將延長。
  5. Water adhesives. aminoplastic. determination of conventional gel time at different temperatures

    水性粘合劑.氨基塑料.不同溫度下膠凝時間的常規測定
  6. Test method for gel time of solventless varnishes

    無溶劑清漆膠凝時間的試驗方法
  7. Composites - prepregs - determination of gel time

    復合物.預浸膠體.膠凝時間的測定
  8. Test method for gel time of tar acids

    焦油酸膠凝時間的試驗方法
  9. Determination of gel time of thermosetting powder coatings at a given temperature

    熱固性粉末塗料在給定溫度下膠化時間的測定
  10. Standard test method for gel time of carbon fiber - epoxy prepreg

    碳纖維環氧樹脂預浸料坯凝固時間的標準試驗方法
  11. Testing methods for paint - part 9 : coating powders - section 1 : determination of gel time of thermosetting coating powders at a given temperature

    塗料的試驗方法.第9部分:塗料粉末.第1節:在給定溫度下測定熱固性塗料粉末的膠凝時間
  12. Basic silicones for industrial use. determination of gel time at a given temperature. method using automatic equipment with rotary motion

    工業用基礎硅塑料.在規定溫度下膠凝時間的測定.自動旋轉設備法
  13. Basic silicones for industrial use. determination of gel time at a given temperature. method using automatic equipment with alternate motion

    工業用基礎硅塑料.在規定溫度下膠凝時間的測定.自動往復運動設備法
  14. It was shown that the gel time and rf carbon aerogels properties were mainly determined by the catalyst content ( r / cat ) and reactant concentration

    催化劑含量（ r cat ）和反應物濃度是影響凝膠化時間和氣凝膠性質的主要因素。
  15. Standard test method for gel time of solventless varnishes

    無溶劑清漆凝固時間的標準試驗方法
  16. Standard test method for gel time and peak exothermic temperature of reacting thermosetting resins

    活性熱固樹脂膠凝時間和最大放熱溫度的標準測試方法
  17. It are general purposed, are easy to control the gel time, it have good color, good puriety, cured time is stable

    過氧化環已酮h4份（或過氧化甲乙酮m ） 2份
  18. The results show that the gel time of the resol prepared in this paper is much longer than that of resol catalyzed with normal alkali such as ammonia and it is more stable when temperature is under 160 ; while temperature exceeds 160, it cures very fast

    結果表明，合成的酚醛樹脂中有大量醚鍵，常溫下它的凝膠時間很長，固化速度慢，溫度大於160后，醚鍵分解產生甲醛，促進固化，凝膠時間迅速減小，固化很快。
  19. First of all, prepare srtio3 powder materials by sol - gel process and solid phase synthesis process. stir time, gel time, gel temperature, heat treat temperature and so on are researched in sol - gel process

    用固相合成法制備鈦酸鍶粉體材料中研究了ti / sr比、研磨方法對制備鈦酸鍶粉體材料的影響。
  20. Methods of test for paints - testing of coating powders - determination of gel time of coating powders

    塗料試驗方法.塗粉試驗.第j3部分:塗層粉末凝膠時間測定
分享友人
分享到 Line

分享到臉書