globe valve 中文意思是什麼
globe valve
解釋
【機械工程】球(形)閥。-
Globe valve - potential pressure life test regulation
截止閥.靜壓壽命試驗規程 -
Sun hydraulik gmbh offers offers to screw - in valves, globe valves and valve housing
提供軸承箱、軸承體、閥體、閥箱、閥套、閥門外殼及其它產品。 -
Face - to - centering dimensions for flanged globe - style angle control valve bodies
法蘭球式角度控制閥體的端面至中心尺寸 -
Tag location for gate and globe valves is typically on the valve yoke or body / bonnet flange
閘閥和截止閥的標簽位置通常在閥門軛架或閥體/閥蓋法蘭上。 -
Automatic steam stop - check angle - globe valves are best on medium - pressure steam service where the sliding action of the semi - plug disc assembly permits the valve to serve as a shut - off valve, a throttling valve and a check valve
自動蒸汽截止止回閥和角式截止閥適用於中壓蒸汽管道系統,此時半插入式閥瓣的滑動作用使得閥門能夠起到關閉閥、節流閥和止回閥的作用。 -
Crane globe valves are highly efficient for services requiring frequent operation and throttling when pressure drop across the valve is about 20 % of inlet pressure
當通過閥門的壓降為管路壓力的20 %左右時,美國克雷恩截止閥就能夠高效應用在頻繁操作和節流的應用場合。 -
Rubber lined globe valve
襯膠截止閥 -
Non - return ( stop - check ) valves provide the same function as a globe valve with the addition of providing piston - lift - check valve protection in the event of backflow
逆止閥(截止止回閥)具有與截止閥相同的功能,還有活塞提升式止回閥的功能,防止出現意外的迴流。 -
This valve is normally automatic work, in a direction of flow of fluid under pressure, the globe valve opening ; the opposite direction of fluid flow, the fluid pressure and the self - valve coincidence role in the valve seat valve, thereby cutting off flow
通常這種閥門是自動工作的,在一個方向流動的流體壓力作用下,閥瓣打開;流體反方向流動時,由流體壓力和閥瓣的自重合閥瓣作用於閥座,從而切斷流動。 -
Recommended for close throttling and most all severe conditions, not to exceed the valve ratings. available for 200 and 300 swp globe and angle valves
建議用於關閉節流和大多數嚴酷的環境,但不能超過閥門的額定值。配置在200和300swp截止閥和角閥上。 -
Globe valve indicates that the stem drive disc along the central spindle of seat make lifting movement, it is a sort of common stop valve. which is mainly used to connect and disconnect medium in pipelines. generally, it is not used to adjust flow
截至閥是指啟閉件(閥瓣)有閥桿帶動並沿閥座中心軸線做升降運動的閥門,是一種常用的截斷閥,主要用在接通或截斷管路中的介質,一般不用於調節流量。 -
As a general rule, an adequately sized globe valve ( i. e. with pipe velocity between 15 to 25 ft / sec for water and 200 to 300 ft / sec for steam ) should not be throttled down below 35 % of its maximum full open cv capacity ( approximately 20 % of full stroke )
一般而言,通徑足夠大的截止閥(例如管道內水流速度在15至25英尺/秒之間,蒸汽流速在200至300英尺/秒之間) ,節流后的流量不應該小於完全開啟狀態流量(流量系數大約為全沖程的20 % )的35 %以下。 -
Example : is a 2 " 600 class stainless steel bolted bonnet globe valve with ms trim
例子:是通徑為2英寸,壓力為600磅級的不銹鋼螺栓閥帽截止閥,帶ms閥內件。 -
Globe diaphragm valve
截止式隔膜閥 -
Angle globe valve
折角球形閥 -
Globe valves should be installed and welded with the disc in a fully closed position to prevent damage to the valve during installation
應該在截止閥閥瓣處于完全關閉狀態下進行安裝和焊接,以避免在安裝過程中隊閥門造成損壞。 -
Plunger globe valve
柱塞截止閥 -
The valve type shall be globe valve
閥體型式為直通型柱塞閥 -
Stopvalves for domestic water supply - two - way valves - vertical bonnet type pn 10 ; straight pattern globe valve ; technical rule of the dvgw
家庭用供水截流閥.雙路閥.立式閥帽型pn10 :直線型球形 -
The fig. 1710 balancing globe valve is a straight pattern design having the stem / disc arrangement vertical to the direction of flow compared to conventional oblique " y " pattern globe valves
型號1710平衡截止閥是直線型結構,其閥桿與閥瓣垂直於水流方向,而不是常規的傾斜式y形截止閥結構。
分享友人