heat aging 中文意思是什麼

heat aging 解釋
加熱老化
  • heat : n 1 熱；熱力；熱度；熱量。2 體溫；發燒。3 （氣候的）高溫，暑氣。4 【冶金】熔煉的爐次；裝爐量；一...
  • aging : n. 1. 陳釀。2. 熟化。
  1. In this paper, 6013al / sicp / gr metal matrix composite ( mmc ) was produced by spray codeposition, by means of changing the medium of quenching, influence of five types of heat treatment system ( furnace cooling, air cooling, water quenching, dry ice quenching, liquid nitrogen quenching ) and different aging temperature on the damping was studied systematically

    本文採用噴射共沉積方法制備了6013al sicp gr金屬基復合材料（ mmc ） ，通過改變淬火介質，較為系統地研究了五種熱處理制度（爐冷、空冷、水冷、乾冰冷及液氮冷）以及不同時效溫度（ 120 、 150 、 170 、 190及210 ）對6013al sicp grmmc阻尼性能影響。
  2. Our company endeavors to quenching & tempering, normalizing, tempering, high and medium temperature quenching, mesh belt furnace quenching, carbonizing, aging subzero and high temperature heat treatment, etc

    本公司是一家致力於從事調質、正火、回火、高中溫淬火、網帶爐淬火、滲碳、時效冰冷及其高溫熱處理的廠家。
  3. Abstract : through contrast test ， characters of ig sealant filled by mineral oil were compared with those of the sealant unfilled by mineral oil ， such as durability ， heat aging resistance ， adhesive ability and the compatibility with hot melt butyl sealant ， and the ultraviolet irradiating resistance of the ig made by them

    摘要：本文通過對比實驗，比較了摻油和未摻油中空玻璃密封膠的耐久性、熱老化性能、粘接性能以及與熱熔丁基密封膠的相容性，比較了其製造的中空玻璃的耐紫外輻照性能。
  4. Through contrast test, characters of ig sealant filled by mineral oil were compared with those of the mineral oil unfilled sealant, such as durability, heat aging resistance, adhesive ability and the compatibility with hot melt butyl sealant, and the ultraviolet irradiating resistance of the ig made by them

    摘要通過對比實驗，比較了摻油和未摻油中空玻璃密封膠的耐久性、熱老化性能、粘接性能以及與熱熔丁基密封膠的相容性，比較了其製造的中空玻璃的耐紫外輻照性能。
  5. Abstract : through contrast test, characters of ig sealant filled by mineral oil were compared with those of the sealant unfilled by mineral oil, such as durability, heat aging resistance, adhesive ability and the compatibility with hot melt butyl sealant, and the ultraviolet irradiating resistance of the ig made by them

    本文通過對比實驗，比較了摻油和未摻油中空玻璃密封膠的耐久性、熱老化性能、粘接性能以及與熱熔丁基密封膠的相容性，比較了其製造的中空玻璃的耐紫外輻照性能。
  6. However, this dissertation mainly focuses on diesel catalyst aging mechanism including heat deterioration and performance degradation caused by toxic substance. following the above conclusions, a fast aging test cycle is produced which consists of three stages

    論文的主體分析了柴油機氧化催化劑的老化機理，主要是熱失活和化學中毒老化，研究了我國主要幾種柴油機的排氣溫度特性，並在催化劑老化機理基礎上提出車用柴油機氧化催化器快速老化試驗循環，即三段式老化循環。
  7. Standard test method for heat aging of asbestos textiles

    石棉織物熱老化的標準測試方法
  8. Standard practice for heat aging of plastics without load

    無負荷塑料製品熱老化的標準實施規程
  9. Rubber, vulcanized - test method of aging by heat and air pressure

    硫化橡膠壓力空氣熱老化試驗方法
  10. Standard practice for heat aging of oxidatively degradable plastics

    氧化降解塑料熱老化標準規范
  11. Rubber, vulcanized - test method of damp heat aging

    硫化橡膠濕熱老化試驗方法
  12. Characteristics : as a result of cold processing aging heat treatment, this product has a tensile strength of over 1100mpa

    特性：通過冷間加工時效熱處理，拉伸長度達到1100mpa以上
  13. At the same time, water quenching at 190 aging exhibit the highest damping capacities. compared with furnace cooling which show the highest damping capacities in five heat treatments, it show higher damping capacities when tempera ture is under 120 and above 290. further more, it show constantly damping value ( tan above 0. 004 ), but the damping value of furnace cooling is just 0. 0015 under 75

    水淬試樣在190的時效溫度下有最高的阻尼性能，通過與爐冷試樣的阻尼性能（五種熱處理制度爐冷試樣的阻尼性能較高）對比發現，在溫度低於120 、高於290范圍，水淬試樣在190時效溫度下的阻尼性能均高於爐冷試樣的阻尼性能，在120 290之間，它的阻尼性能低於爐冷試樣的阻尼性能，而此溫度區間正好是位錯內耗峰出現的溫度范圍。
  14. Products of te series have wonderful appearance and good functions of bearing voltage and aging. but the capability of bearing high heat is a bit poor

    Te系列產品擁有極佳的產品外觀和耐電壓，耐老化性能，耐高溫性能稍差。
  15. Based on an advanced formula, the plastic parts are made of injection - molded, high - strength engineering plastic pc by numerical control equipment, therefore effectively prevent products from aging caused by coldness, heat, oxygen and ultraviolet radiation

    整套接頭筒塑件採用科學配方的高強度pc工程塑料，經過數控設備注塑成型，能有效地阻止大自然中冷熱氧和紫外線引起的材料老化，並且具有優良的力學強度。
  16. Practice for heat aging of oxidatively degradable plastics

    可氧化降解塑料的加熱老化實施規程
  17. 4, good resistance to milling, heat, aging and corrosiveness and long service life

    4耐磨耐熱耐老化耐腐蝕，使用壽命長
  18. Standard test method for effects of heat aging on weight loss, cracking, and chalking of elastomeric sealants

    熱老化對彈性填縫料重量損失破裂及粉化影響的標準試驗方法
  19. Standard test method for effects of heat aging on weight loss, cracking, and chalking of elastomeric sealants after cure

    彈性體密封劑凝固后熱老化對重量損失裂開和粉化影響的標準試驗方法
  20. Standard test method for extensibility after heat aging of cold liquid - applied elastomeric waterproofing membranes

    冷液彈性防水薄膜熱老化后伸展性的標準試驗方法
分享友人
分享到 Line

分享到臉書