heat flow equation 中文意思是什麼
heat flow equation
解釋
熱方程-
Regressed the experimental date with linear use minimal dual multiply method. got the empirical equation of heat transfer and flow resistance in laminar, transitive and turbulent zone
Reb隨肋高h 、肋軸向間距pt的增大而減小，隨肋寬的增大而增大。 -
Adopted numerical value integral method into the explain of the basic heat - conduct differential equation based the stabilization flow. get temperature changes rule of the cold - blowing and hot - blowing period of the cold - cumulating and dry - able tin
採用數值積分法對基於穩定流的基本傳熱微分方程組進行求解，進一步了解了影響蓄冷器效率的主要因素。 -
The interior temperature distribution and ablation model of projectile wing is established from general transmitting heat differential equation ; at the same time, the heat flow density and pressure distribution model of projectile wing is also established
從一般形式的導熱微分方程出發，逐步建立了彈翼內部溫度分佈和燒蝕的數學計算模型；與此同時，建立了彈翼表面的熱流密度和壓力分佈的數學模型。 -
The formulation for the flow model is given using the finite element / control volume ( fe / cv ) technique based on darcy ' s law of creeping flow through a porous media. the heat transfer model is based on the two - dimensional, transient heat conduction equation, including heat generation. the cure kinetics model is based on kamal ' s model, and the degree of the resin cure as a function of temperature and time
樹脂流動階段的模擬是根據牛頓流體在多孔介質中的滲流理論，應用darcy定律並使用有限元/控制體技術建立起來的；熱傳遞模型是一個二維瞬態熱傳導方程，考慮樹脂反應放熱；樹脂的固化模型利用了kamal提出的固化動力學方程，將固化度取為時間和溫度的函數。 -
Studying the heat - mass transfer and multi - spices electric - chemical reaction, a dynamic temperature model was deduced for molten - carbonate fuel cell stack. the thermal radiation, shift reaction, and the change of gas spices were considered in this model. establishing momentum equation, the paper has developed a 3d temperature and flow fields model for mcfc stack based on cfd technique
建立了熔融碳酸鹽燃料電池堆內部單體的暫態溫度模型，並考慮了電堆的輻射換熱、轉換反應、反應氣體組分變化對溫度場的影響；根據mcfc的微分控制方程組，考慮氣體組分的熱力學性質及動量變化的影響，利用數值分析方法求解熔融碳酸鹽燃料電池堆的三維流場與溫度場，分析了各作用因素對熔融碳酸鹽燃料電池堆溫度分佈的影響機制。 -
The experimental results of the flow characteristics of the mmc heat sink indicate that the critical reynolds number signifying the transition from laminar flow to turbulent flow is in advance ; under the same experimental conditions, the variation in entrance direction of the microchannel inlet and outlet has little effect on the microchannel ; the experimental values of the friction factor of the de - ionized water in a microchannel agree well with those calculated using the theoretical laminar formula ; furthermore, a comparison of the experimental results and simulation results shows that navier - stokes equation and rng - turbulence model can be used to model the laminar and turbulence flow regions in a microchannel ; meanwhile, the correlations of the flow resistance in the turbulent flow regions for the de - ionized water as the working fluids are obtained from experiments
對歧管式單通道熱沉流動特性的研究結果表明，微通道內流體流態由層流向紊流轉變的臨界雷諾數提前;改變流體的進出口方向對熱沉總壓降造成的影響很小;摩擦系數的實驗值與理論值較接近;數值模擬結果能夠與實驗值較好吻合;並由實驗給出了紊流區流動阻力的實驗關聯式。此外，選用十二烷基硫酸鈉（ sodiumdodecylsulphate ， sds ）以及烷基多糖苷（ alkylpolyglycoside ， apg ）作為減阻添加劑，研究了表面活性劑添加對微通道流動特性的影響。 -
The result shows that the heat transfer coefficient within the hollow fiber module with laminar flow can be calculated based on the correlation. by analyzing the equation, it was founded that the heat transfer coefficient under laminar flow is almost independent of the feed flow rate. numerical simulation of temperature distribution in hollow fiber membrane module with laminar flow was carried out
首先採用純水為研究體系，研究分析了中空纖維管內的傳熱系數，研究表明，纖維管內的流動屬于層流狀態，其邊界層傳熱系數可用關聯式來計算，由此式看出，層流狀態下，流速對傳熱系數的影響很小。 -
The characteristic of flow and heat transfer in the annular curved eccentric pipes were studied. the convective heat transfer equation and numerical simulation were based on it
摘要討論了環形偏心圓截面彎管內的對流換熱特性，並在此基礎上建立了對流換熱方程。同時採用數值模擬的方法分析了環形偏心圓截面彎管內的流場分佈。 -
In this paper, the continuity equation, the momentum equation, the k equation and the e equation are used to set up the theoretic model. the flow in the intake port is looked upon as the three - coordinate steady flow, but the heat transfer between the all and the flow in the intake port is n ' t considered
本論文利用連續性方程、動量方程、 k方程、方程建立氣道流動理論模型，將氣道內流體看作三維定常流動，不考慮氣道壁面與流體之間的熱傳遞。
分享友人