heating wall 中文意思是什麼

On the basis of expound the theory of building exterior - protected construction energy consumption and the gene of influence the building energy, set up mathematics model, this article discuss the mechanism of dispelling the heat of the buildings " thermal bridge and the complication that influence it, and then synthetic analysis and calculate the influence range of building thermal bridge in exterior - protected construction column thermal bridge to the building outer wall get the conclusion that when the construction column can satisfy the building stress - area, in bulgy construction column dispel less heating than out bulgy construction column. but if the pole stuck out more than 100mm, in bulgy or out bulgy make no difference

本文在闡述建築圍護結構耗熱原理以及影響建築能耗因子的基礎上，採用數值模擬方法，探討了建築熱橋傳熱的基本機理和影響建築熱橋傳熱的因素，進而對建築熱橋在圍護結構傳熱中的影響范圍進行了綜合分析和計算，研究了構造柱熱橋型式對建築外墻能耗的影響，得出了構造柱在滿足建築受力面積要求的情況下，內凸構造柱較外凸構造柱略能減少散熱量的結論，但是凸出過大（ 100mm ）無論內凸還是外凸對建築耗熱都沒有大的差別。

Cylinder dryer is a dind of rotatin continuous drying equipment with internal heating conducting - style, certain thickness of materials film theres to the lower trough of materials under the rotating cylinder. heat is transferred to the internal wall of the cylinder through pipes and misfired ahain to the external wall and to materials film, to evaporate and damnify moisture in materials film so as to dry materials

滾筒乾燥機是一種內加熱傳導型轉動連續乾燥設備。旋轉的滾筒通過其下部料槽，粘附著一厚度的料膜。熱量通過管道輔送至滾筒內壁，傳導到滾筒外壁，再傳導給料膜，使料膜中的濕度得到蒸發、脫濕、使含濕份的物料得到乾燥。

Aimed at the high temperature at furnace roof and wall, great lost of body heat radiation, poor leading heating ability and long soaking time, the compound ceramic fiber coating is used to hold temperature of furnace roof and wall, make the heating loss dropped, shorten soaking time, improve heating ability and reduce evergy consumption

摘要針對環形爐爐頂爐墻表面溫度高、爐體散熱損失大、導致加熱能力低、待溫時間偏長的問題，選用了復合陶瓷纖維保溫塗料，使爐體散熱損失減少，待溫時間縮短，加熱能力提高，且能耗降低。

For example, the temperature standards, the project adopted a geothermal heating to link with municipal heating networks. the designs of energy - saving insulation wall : extruded ceramic plastic plate, three - window design aluminum - plastics which meet energy requirements, and also to improve the insulation quotiety i

如溫度標準，小區採取了地熱供暖方式，與市政供熱管網連接，採取節能保溫墻面體設計：陶粒加擠塑板，窗戶採用三玻鋁塑窗設計，即達到節能要求，又提高了保溫系數。

This paper introduces that the diffuse heat heating furnace is reduced the consumption of fuel is debased and the preferable effect is got, using the multicrystal mullite fibrous stickup lump to heat preservation in heating furnace wall

摘要採用多晶莫來石纖維貼面塊對加熱爐爐內壁保溫，減少了爐體的散熱損失，降低了爐子燃耗，取得了較好的效果。

Avoiding the difficulties of detecting the difficult parameters in furnace control and of building up the models, integrated with fuzzy control and conventional pid control, abb ’ s control it system is used to predict the bloom surface and center temperature directly based on the temperature of furnace wall easily to be detected so that the temperature settings in various furnace sections can be self - corrected, the furnace temperature of each section self - adjusted and on - line parameters of combustion control self - optimized. in addition, the heating parameters and the operating status of the field plant can be monitored with alarm

採用abb公司的controlit控制系統，避開爐子控制中遇到的困難參數檢測及建模困難等因素，直接根據容易檢測的爐壁溫度來推知鋼坯表面溫度及鋼坯中心溫度，將模糊控制技術與常規pid控制相結合，實現各段溫爐設定值自修正、各段爐溫自協調、各參數在線自整定的自尋優最佳燃燒控制;對熱工參數、現場設備的運行情況進行監視、報警，實現爐膛壓力、管道壓力、換熱器的保護控制，並將重要參數送往廠級mis網路。

The thesis adopted the effective heat transfer coefficient to heating load calculation, through it, we discover that : the heat consumption of the lowest story door, highest story door and the door stick to gable wall is more than the center door of the building, further approved the necessity that the communal heating load calculation are abstracted and allocated averagely

本文採用有效傳熱系數法對耗熱量進行計算，通過本文的研究發現：住宅的底層用戶、頂層用戶及有山墻用戶的耗熱量遠高於中間住戶的耗熱量，進一步說明了提取公共耗熱量並將之按面積平分的必要性。

The general situation of natural gas source in china and the economy of wall - mounted gas boiler for individual heating are analyzed, and the current situation analysis and forecast on heating load of gas heating are made

摘要分析了我國天然氣的氣源概況和燃氣壁掛爐分戶採暖的經濟性，進行了燃氣採暖熱負荷的現狀分析和預測。

Don ' t apply direct heat. don ' t use hot water, a heating pad or a heating lamp to warm the victim. instead, apply warm compresses to the neck, chest wall and groin

不要直接加熱。不要給患者使用熱水、電熱褥或加熱燈等設備。應該使用熱的敷布敷在患者的胸部與腹股溝部。

Through the analysis and studying of this subject, we can make conclusion as followed : during the whole heating season, the change law of the energy consumption of the thermal bridge is with the change law of the meteorological condition inside and outside the room : when airs temperatures indoor is steady, thermal bridge energy consumption increases with reducing of air temperature outside the room, reduce oppositely. the different position and the different structure patterns of the thermal bridges, even under the same meteorological condition inside and outside of the room, energy consumption of the building is different, and impact on heating energy consumption is different, this is mainly caused by the difference of the constructs thermal bridge and different influence in term of out wall, which lead to total mean heat - transfer coefficient different, when the heat - transfer coefficient is relatively small of outer wall, the impact of wall body is more obvious on heat - transfer coefficient of the thermal bridge

然後確立了在節能建築中熱橋耗熱量與室內外氣象參數和熱橋構造型式的關系，分析與研究並得出：在整個採暖季節中，熱橋的能耗隨著室內外氣象條件的變化規律是：在室內空氣溫度一定時，熱橋能耗隨著室外空氣溫度的降低而增大，相反減小；不同部位的熱橋，其構造型式不同，即使在相同的室內外氣象條件下，產生的能耗也是不同的，並且對採暖能耗的影響也不同，這主要是由於不同構造的熱橋對外墻的總平均傳熱系數的影響不同所造成的，並且當外墻主體的傳熱系數較小時，熱橋對墻體的傳熱系數的影響更加明顯。

Another innovation, is the "trombe wall" hybrid solar-heating system.

另一個發明是「特蘭勃墻」，混合型太陽能加熱系統。

Treatment for three stubborn problems in the safe and economical operation of cfbc boiler wear prevention of wall and heating surface discharge and cooling of bottom slag

爐壁和受熱面防磨的治理及爐底渣排放與冷卻

It is widely applied to the stove top, shove head, stove door and burmer brick, the binding of cooling - tube and groove bottom of the molten steel mouth of the heat stove, meantime empopyed in the field of the step stove bottom, the fir - proof wall of the circular stove, the cover, the protruding tape and sand sealing mouth of the equal - heating stove, the triangle, the spray gun and meltingiron groove of electric stove and also including fire - resistant material used in the refine stove and the stove door

加熱爐的爐頂、爐頭、爐門、燒嘴磚、水冷管包紮、出鋼槽槽底、步進爐爐底、環形爐檔火墻、均熱爐的爐蓋、凸出帶、砂封口、中間包包蓋、電爐三角區、鐵水包襯里、爐外精煉用噴槍，底吹氧煙道、鐵水溝蓋、檔渣堰、高爐中各種耐用火料襯里煉焦爐爐門等。

Application of wall - mounted gas water heater in heating

壁掛式燃氣熱水器供暖的應用

The main characters of the thermal fluid activity are recognized as follow : many types and stages of veins are widely developed ; vitrinite reflectivity of different areas varies apparently with the depth ; there was a high temperature field during the formation of the thermal fluid, meanwhile, the volcaniclastic rocks were modificated by the thermal fluid activity, for example, sericitization of plagioclase, chloritization of volcanic detritus in andesitic detris tuff ; in the tufaceous mud, the thermal fluid activity accelerates " maturating " of the organic carbon by heating ; and the trace elements show an anomaly in the wall rocks

同時，受熱流體活動的影響，熱流體對火山碎屑巖具有一定改造作用，如在安山質巖屑凝灰巖中，斜長石絹雲母化、火山巖巖屑綠泥石化明顯；在凝灰質泥巖中，熱流體對圍巖中有機碳具有明顯的「催熟」加熱作用，微量元素則出現異常現象。

Auxiliary equipment. cooking. heating. push - on connectors for rubber tubes and caps intended to be fitted on certain domestic appliances using mains distributed combustible gases and on g 1 2 b male wall - mounted taps

輔助設備.烹調.加熱.使用管道供燃氣的某些家用設備上安裝的橡膠管件和密封蓋的推入式連接器和g1 2陽螺紋墻裝氣閥的連接器

In this paper, the pier - wall models respectively built with steel - fiber concrete and ordinary concrete were tested for revealing their early bebaviors of thermal strain and thermal stress caused by adiabatic heating

為此進行了鋼纖維混凝土和普通混凝土2個墩墻結構的模型試驗，比較了二者的溫度及溫度變形的特性。

Elements should have their heating sections in the furnace chamber so that no portion of the heating section extends into the furnace wall or refractory plug

安裝時應確保其發熱部在爐腔內，沒有超出爐壁或者難熔插栓的部分。

This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。

Model w still may use disassembled u type heating pipe. when maintenance, it can be removed out to the still. so it is very convenievt to clean the outer wall of heating pipe and the inner wall of still

W型之蒸餾新釜採用可拆式u型力口熱管，在檢修時可將u型加熱管移出釜外，便於對加熱管外壁及蒸釜內壁進行清洗。