high carbon heat 中文意思是什麼
high carbon heat
解釋
高碳鋼熔煉-
The temperature distribution on the high temperature side of an electric tunnel furnace is analysed and simulated on the basis of the principle of thermal radiation by the way of thb ( thermal heat balance ). the heated silicon carbon sticks are decomposed into innumerable tiny heating faces, which exchange the heat with the heated materials. a numerical model based on the radiation intensity law is constructed to calculate the energy absorbed by the heated materials and simulated by a computer. the results showed that the even distribution of temperature can be obtained by optimizing the arrangement of the silicon carbon sticks according to the calculation results to make the structure design more reasonable. these calculation results have been used in the practical designs and the expected objectives achieved
利用熱輻射原理，採用熱平衡法對電熱隧道窯的高溫恆溫區溫場進行了分析和模擬.計算中將發熱棒分解為無數微元發熱面與燒結體進行熱交換，依據輻射強度定律，建立了燒結體接收能量的數學模型，並用計算機進行了模擬計算.結果表明，依據模擬結果來優化硅碳棒的排布，可使結構設計更加合理，進而可以獲得分佈均勻的恆溫區溫場.計算結果已在窯爐設計中應用，實踐效果良好 -
Wear resistant layer of cylinder and double - layer liner in catalyst creaking apparatus ( without or with tortoiseshell net can be used ), inner liner of carbon monoxide exhaust - heat boiler, pouring at site for furnace roof with high temperature of heating furnace of steel rolling, different forging furnace, resistance furnace, the prefabricated parts can also be made
催化裂化裝置中的筒體耐磨層及雙層襯里， （無龜甲網和有龜甲網均可採用）及一氧化碳余熱鍋爐的內襯，也適用於軋鋼加熱爐、各種煅造爐、電阻爐的爐頂、爐墻、爐底高溫部位的現場澆注，可製成預制構件。 -
Through the comparison between freeze - drying and heat - drying, the agglomeration and the desorption of the precursor on carbon support can be alleviated with freeze - drying method. the effects on the electrocatalysts by pretreatments of carbon support, dispersant and precursor are studied. the result shows that pretreatment of the carbon support by kmno _ 4 can add oxygen - containing functional groups on the surface of carbon, which can reduce the hydrophobicity of the carbon support, and then make it much easier for carbon to dissolve in water to form suspension ; isopropyl alcohol can make the carbon support in high dispersion in the precursor solution, which can make the precursor absorbed on the surface of the carbon
採用高錳酸鉀氧化預處理的碳載體比表面積較大，表面含氧官能團數量較多，親水性較好，有利於前軀體在碳載體表面的吸附;選取異丙醇作為預凍液中的分散劑，有利於碳載體在前軀體溶液中的分散，容易實現前軀體離子在碳載體表面的穩定吸附和分散;使用酸性pt （ no _ 2 ） _ 2 （ nh _ 3 ） _ 2作為前軀體，可以使前軀體離子和碳載體表面的酸性含氧官能團發生離子交換反應，使得前軀體離子吸附量增大，分散更加均勻，以上三種因素的選取都可以得到催化活性更高的pt / c催化劑。 -
Specifications for heat - treatment of rolling bearing parts made from high carbon chromium stainless steel
高碳鉻不銹鋼滾動軸承零件.熱處理技術條件 -
The material of electro - fused magnesia sinter is selected from special grade a natural magnesite or high - purity caustic calcined magnesite, which is fused in arc furnace to finish the products. the products possess high purity, crystal with and compact texture, have high heat - vibration steady and cinder corrosion resistant, it is used for making high quality magnesite bricks, magnesia - carbon bricks
電熔鎂砂是用精選的特a級天然菱鎂石，在電弧爐中熔融制得，該產品具有純度高，結晶緻密，抗渣性強熱震穩定性好，是製作高檔鎂磚，鎂碳磚及不定形耐火材料的重要原料。 -
In the ensuing excitement, researchers advanced many theories to explain them : leaking aquifers ( which would be inexplicably perched high on crater rims ) ; pressurized geysers of water ; high - pressure outbursts of carbon dioxide gas ; volcanic heat sources at depth
在接下來的一陣狂熱中，研究者提出許多的理論來解釋： ?漏的含水層（在隕石坑外緣必須被抬升至非常高的高度） 、受壓的間歇泉、高壓噴出的二氧化碳氣體、深層的火山熱源等。 -
The high speed steel of composite roll is characteristic of high carbon and high alloy elements. so it is easy to form a lot of netlike carbides. these carbides which are very hard and fragile and are very difficult to be eliminated by heat treatment can depress the properties of high speed steel
復合軋輥用高速鋼具有高碳和高合金的特徵，容易形成大量網狀碳化物，這些網狀碳化物又硬又脆，會嚴重降低高速鋼的性能，且難以用熱處理的方法予以消除。 -
Specification for heat - treatment of rolling bearing parts made from high carbon chromium steel
高碳鉻軸承鋼滾動軸承零件熱處理技術條件 -
This dissertation focuses on how to develop a high performance damping mechanism based on multi - energy transitions, which is independent or little dependant with the viscoelasticity of polymer matrix. three sections are mainly included in this dissertation as follows : chlorinated polyethylene ( cpe ) / piezoelectric ceramic ( pzt ) / vapor grown carbon fiber ( vgcf ) composites ; cpe / 2, 2 ' - methylene - bis - ( 4 - methyl - 6 - cyclohexylphenol ) ( zkf ) / vgcf composites ; organic hybrids made from cpe and small molecules cpe / pzt / vgcf composites : the damping composites of multi - energy transitions mechanism were produced by mixing pzt and vgcf into cpe. in this system, the mechanical vibration energy that was transmitted to cpe was found to convert into joule ' s heat through conduction paths between vgcf in the polymer matrix, so the vibration fades away
本論文主要包括三個方面的研究內容： ?氯化聚乙烯（ cpe ） /壓電陶瓷（ pzt ） /氣相生長碳纖維（ vgcf ）復合材料； ? cpe /雙[ （ 2 -羥基- 3 -環己基- 5 -甲基） -苯基]甲烷（ zkf ） / vgcf復合材料； ? cpe基有機小分子混雜型復合材料cpe / pzt / vgcf減振復合材料：利用壓電和導電填料填充高聚物基體，當復合材料受到機械振動時，通過高聚物基體將機械振動能傳遞到壓電陶瓷粒子上，利用壓電陶瓷的壓電效應，將機械能轉換成電能，則電流在導電粒子產生的迴路中流動，由於導電迴路具有一定的電阻，所以電能又轉變成熱能耗散掉，從而起到減振的目的。 -
In order to make investigators know about the current research state of preparation of the carbon / graphite materials with high density and strength from mesocarbon microbeads, and direct the research, development and production, in this review, the influence of preparaed mesocarbon microbeads from various raw materials and methods of preparation, ball diameter of carbosphere, preoxidation temperature and time, moulding pressure and time, heat treatment temperature and heating rate, holding time on the mechanical properties and microscopic structure of carbon / graphite product were discussed by us
摘要為了對中間相炭微球制備高密高強炭石墨材料的研究現狀有所了解，並且對實驗和實際生產起到指導作用，本文通過參閱大量中外文獻，討論了不同原料及制備方法制得的中間相炭微球、炭微球的球徑、預氧化溫度及時間、成型壓力及時間、熱處理溫度及升溫速率、保溫時間對炭石墨製品的力學性能及微觀結構的影響。 -
It has been widely used as binder for making heat - insulating board for lundish, featuring stability, high fized - carbon, no poison, no precipitation, etc … it produced so much favourabte comment and trusr from customers
廣泛用於轉爐修補料、乾式中間包振動料、冶金連鑄中間包絕熱板作結合劑，它具有性能穩定、固定碳高、無毒、無沉澱的特點、多年來深受廣大用戶的信任和好評。 -
Purposes : this product applies to fireproof layer and oxygen - resisting layer for low smoke, non - halogen, innocuity, high grade cleaned non - flammable cables and fireproof cables, it can absorbs vast amounts of heat during burning process and forms into a carbon layer to isolate air and prevent the cable from buring further
用途：該產品用作于無鹵低煙、即無公害，高檔潔凈的阻燃電纜和耐火電纜的隔火、隔氧層，在燃燒過程中能吸收大量熱量，並形成碳殼層、隔絕空氣，阻礙電纜進一步燃燒。 -
Made of high - speed mixing polytetrafluoethylene resin and a certain volume of filling agent ( such as carbon fiber, graphite, molybdenum disulfide, glass fiber and bronze powder etc. ) shaped by moulding then through high heat sintering
用聚四氟乙烯樹酯與一定量的填充劑（如：碳纖維、石墨、二硫化組、玻璃纖維、青銅粉等）經高速混合均勻後用模塑成型經高溫燒結製成。 -
We studied the effect of laser quenching ( harden by phase transformation ) on some representative mould steels. through measuring the rigidity on the surface of samples treated by laser heat treatment, and through photographing microstructures of the steel surface, we find many reasons attribute to high hardness. these reasons include ultra - fine grains, high density dislocation and more content of carbon in martensite
我們研究的是激光淬火對幾種典型模具鋼的作用，通過對熱處理后的試樣的硬度分佈的測定，用金相和電鏡觀察金相組織的變化，認為激光熱處理產生高硬度的原因是晶粒細化、高的位錯密度和高的馬氏體含量。 -
Low grade fuels and / or polluted air can cause gum, varnish and carbon deposits to be formed in the carburetor during comustion which can result in rough idling, stalling and incrased gasoline consumption. 3 + 3 cleaner ' s superior formula will effectively remove gum, varnish and carbon deposits when sprayed directly into the carburetor, 3 + 3cleaner will clean carburetors, linkage, automatic chokes, pcv valves, heat risers, the spark plugs and the entiro system while lubricating and femoving moistuer on all moving parts, use 3 + 3 cleaner to restore efficiency, increase engine power maintain high gasmileage and have a smooth running engine
空氣和汽油中的不純物質，在汽車使用過程中會產生污垢和炭積物，阻塞汽車的化油器（呼吸系統） ，使汽車無力及加油不暢順， 3 + 3牌化油器強力清洗劑獨有的特殊配方，直接噴入于化油器內，能迅速有效地清除洗化油器，火花塞及燃油系統的油漬污穢和炭積物，並對轉軸等旋轉部位提供潤滑及防銹保護，減少積炭的產生，使引擎起動順利及平穩運轉，增強馬力及節省燃油 -
The results show that, when the hardfacing process is not appropriate, the thick martensite structure with high carbon content will form in the overheat region of heat affected zone, and the high residual stress occurred, which are the primary causes resulting in crack
結果表明，堆焊工藝制定不當，熱影響區的過熱區形成高碳粗大馬氏體組織及保留了較大的焊接應力，是導致堆焊層開裂的主要原因。 -
With the orthogonal experiment method, the heat rolling processing parameters of the high - grade carbon steel ( 20 ) are established so as to realige the control and enhance the compositive mechanical property and cold crooked performance which advances the quality of the product
運用正交試驗方法，確定優質碳素結構鋼（ 20 ）鋼板熱軋工藝參數，以便實現控制，提高20鋼板的綜合機械性能和冷彎工藝性能，提高產品質量。 -
Abstract : with the orthogonal experiment method, the heat rolling processing parameters of the high - grade carbon steel ( 20 ) are established so as to realige the control and enhance the compositive mechanical property and cold crooked performance which advances the quality of the product
文摘:運用正交試驗方法，確定優質碳素結構鋼（ 20 ）鋼板熱軋工藝參數，以便實現控制，提高20鋼板的綜合機械性能和冷彎工藝性能，提高產品質量。 -
The carbon fibers with low strength are broken easily according to thermal tension and bend stress damage models, and the carbon fibers with high modulus are broken easily according to thermal shear stress damage model in spite of less damage caused by heat. the carbon fibers with surface glue of epoxy resin are damaged easily in physical and chemical ways because of high oxygen extent and rigidity of epoxy resin
低強度碳纖維容易在熱應力拉伸或彎折破壞模式下損傷；高模量碳纖維高溫損傷小，但國防科學技術大學研究生院學位論文容易以熱應力剪切破壞模式下斷裂;環氧樹脂表面膠剛性較大，氧含量較高，使碳纖維容易受到化學損傷和熱應力彎折損傷，均不宜用來制備c燈sic復合材料。 -
Motor nozzle : the product adopts hard alloy or carbon steel heat treatment and receives precision grinding and polishing by professional processing equipment. therefore, it boasts high resistance to flexure and to wear and is extensively applied in fields of series, fan, micro - motor and motor for wire coiling of stator and rotor
產品描述： ：此產品以超硬質合金或碳鋼熱處理為材料，使用專業加工設備精密磨削和拋光加工而成，有極好的抗彎強度、耐磨性，廣泛用於串激、風扇、微電機、馬達等行業的定子、轉子的線圈繞制上。
分享友人