inclined joint 中文意思是什麼
inclined joint
解釋
斜縫-
From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints
採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。 -
As far as the solid inclined column - wall transfer r. c joint is concerned, the inclined column with a bigger angle 、 transfer beam and square column work as a whole, and the load transfer mechanism is similar to the transfer beam. the stress state in the wall is much more even, so the effect of transfer is much better than that of the hollow inclined column - wall transfer r. c joint
對無孔斜柱轉換節點而言，由於斜柱與轉換梁和方柱形成了一個整體，而且斜柱角度較大，因而其傳力機制和加腋的轉換梁類似，但薄壁柱中的應力分佈更為均勻，轉換效果更好。 -
According to test results of two specimens of local transfer rc joint from inclined column to beeline - shaped wall under vertical static loads and results of corresponding finite element analysis ( ansys ), fundamental behaviors of the joint are achieved, which include paths of vertical load transfer before and after cracking, stress distributions, occurrence and development of cracks and final failure mode of the joint
本文通過兩個鋼筋混凝土斜柱?一字形薄壁柱局部轉換節點在豎向荷載作用下的靜力試驗以及有限元分析，獲得了該節點的基本性能，其中包括開裂前後的豎向荷載的傳遞路徑、試件應力分佈，裂縫的發生、發展，及試件最後的破壞形態等。 -
As far as the hollow inclined column - wall transfer r. c joint is concerned, the paper introduced the truss model to calculate the internal forces of transfer beam, inclined column and square column
在有孔斜柱轉換節點中引入了桁架模型以確定轉換梁、斜柱及方柱的內力。 -
The result indicate that there is much difference between the hollow inclined column - wall transfer r. c joint and the solid inclined column - wall transfer r. c joint on the mechanism of load transfer
結果表明有孔斜柱轉換節點和無孔斜柱轉換接點的豎向受力性能和傳力機制存在著明顯的差異。 -
As far as he hollow inclined column - wall transfer r. c joint is concerned, the stress state of transfer beam is very critical, because it bears not only the vertical load transferred from the wall, but also the axial load initiated by the inclined column
對有孔斜柱轉換節點而言，轉換梁的受力最為不利，它不僅承擔由薄壁柱傳來的垂直荷載，而且還承擔由斜柱水平分力引起的軸向拉力，即截面上有彎矩、剪力和軸力的共同作用。
分享友人