induction heat treatment 中文意思是什麼
induction heat treatment
解釋
感應加熱熱處理-
Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously
應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。 -
The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar
研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。 -
Development and application of induction heat treatment technology and equipment
感應熱處理技術及工藝裝備的開發與應用 -
Induction heat treatment
感應加熱熱處理 -
Abstract : this paper introduced the induction hardening experiment of components ? the gear - park and the drive support sprocket. give some advise on the pearlitic malleable iron ' s induction heat - treatment, and show coil design intending to meet the harden profilc according to the drawing
文摘:本文介紹變速箱零件? ?駐車齒輪和鏈輪支架的感應淬火試驗工作，提出對可鍛鑄鐵感應淬火中值得注意的問題及針對這兩種零件的特殊硬化層要求而設計的感應器。 -
Specification for bending and heat. treatment of 921a bulb flats by means of mf induction
921a球扁鋼中頻彎曲和熱處理技術條件 -
Founded in september 1997, the company occupies an area of 35000 square meters and has 50 staffs, including 3 engineers, 2 vice senior engineers and 4 engineers. with the help of some domestic specialists who engaged in the research on induction heated quenching - tempering treatment in weapon and space industries. we developed the first induction heat oil tempered elastic wire production line in china by ourselves. this production line was put use in august 1998, and was enlisted in the spak programme in 2000 serial number : 369, programme code : 00b101d691004
創建於1997年9月，佔地35000平方米，員工50名，其中研究員級高工3名，高工2名，工程師4名。依靠國內一批在軍工企業長期從事感應加熱調質處理研究的專家，自行研製成功國內第一條彈性線材感應加熱油淬火-回火生產線，並於1998年投產。 -
The heat - treatment technology with medium frequency induction heating for driving wheel of crawler tractor is analyzed, and proved being feasible through technical test, data analyzing and trial installation
摘要本文分析了履帶拖拉機驅動輪中頻感應加熱的熱處理工藝，從工藝試驗、數據分析和裝機試驗幾個方面驗證了該工藝的可行性。 -
We have complete set of equipment, 6 production lines from 160 tons to 1600 tons consisted of 48 forging machines and can produce forging products and heat treatment products for mechanical and automobile enterprises. the heating system we adopted is medium frequency induction oven, which can guarantee the forging quality
我公司設備全，由48臺鍛壓設備組成的160t至1600t的6條生產線，可以為機械汽車配套企業生產各種鍛件產品和熱處理產品，加熱方式全部採用中頻感應加熱爐先進工藝，能有效地保證良好的鍛壓質量。
分享友人