injection nozzle 中文意思是什麼
injection nozzle
解釋
噴射管嘴-
Delay pintle catibrating injection nozzle
軸針式標準噴油嘴偶件 -
Simulation results show that better atomization can be realized by enhancing the cavitation intensity via increasing the injection pressure difference or decreasing the nozzle inlet round angle - radius ratio
通過模擬計算可知,提高噴射壓差和減小噴孔入口圓角半徑都可以提高空穴強度,同時也發現提高噴孔長徑比可以使空穴在噴孔出口截面上分佈更為均勻。 -
Based on this model, the effects of geometric and structural parameters, such as injection pressure, rear pressure, length - diameter ratio, inlet round angle - radius ratio and non - axis symmetry of nozzle, on the distribution of the cavitation inside the nozzle are analyzed
基於這一模型進一步分析了噴射壓力、背壓和噴孔長徑比、噴孔入口圓角比、非軸對稱噴孔等幾何結構參數對噴孔內空穴分佈的影響。 -
Our company is specialized in series of diesel engine, electric fuel pump, oil injection nozzle, start machine and accessories used for cars and light duty trucks
本公司專業生產電動燃油泵、噴油嘴及起動機系列產品,適用於轎車、輕卡及柴油機配套產品及配件。 -
Low frequency micro - vibration causes the micro - fluid to produce uniform dispersion and injection which carried out a hydrophobization treatment on the inner wall of micro - nozzle, thus eliminated the spontaneous flowing of micro - fluid inside the micro - nozzle due to wet ting effect so as to let the micro - injection be provided with a digitalized and volume controllable character
壓電陶瓷低頻微振動使得微流體產生均勻的離散和噴射;對微噴嘴內壁進行疏水化處理,從而消除微流體由於濕潤作用在微噴嘴內部的自發性流動,使得微噴射具有數字化量可控的特徵。 -
Based on the analysis of the combustion in cylinder, the thorough research of multiparameters ( engine speed, load, ignition timing, injection timing, injection nozzle type, compression, ignition pattern etc. ) on methanol engine combustion cyclic variations is made on a 1130 single - cylinder diesel engine fueled with methanol
在燃用甲醇燃料的1130單缸柴油機上,通過缸內燃燒分析,對影響甲醇發動機循環變動的各種因素(轉速、負荷、點火提前角、噴油提前角、噴油嘴類型、壓縮比、點火方式等)進行了詳細的研究。 -
Fuel injection nozzle used on small bore diesel engine with swirl combustion chamber
小缸徑渦流室柴油機用噴油嘴的研究 -
Road vehicles - shapes and dimensions of fuel injection nozzle holders for diesel engines - size " p
道路車輛.柴油機燃油噴嘴體的形狀和尺寸.規格p -
Road vehicles - shapes and dimensions of fuel injection nozzle holders for diesel engines - size " s
道路車輛.柴油發動機用燃油噴嘴支架的形狀及尺寸. " s "規格 -
Road vehicles. compression - ignition engines. screw - in injection nozzle holder, type 23
道路車輛.壓燃式發動機.擰入式噴嘴座, 23型 -
Diesel engines - screw - in injection nozzle holders, types 24, 25, 26 and 26. 1
柴油發動機.型號為24 25 26和26 . 1的旋入式噴嘴座 -
Road vehicles ; compression - ignition engines ; screw - in injection nozzle holders, types 24, 25 and 26 ; identical with iso 9102 : 1990
道路車輛.壓燃式發動機. 24 . 25 . 26型螺絲擰入式噴嘴座 -
Simulating results reveal that hydrodynamics of catalysts in riser reactor is very complex due to the effect of injection and catalysts backmix dramatically near the nozzle, reaction products unevenly distributie along the riser height, there exists apparently temperature gap between gas - phase and solid - phase near the nozzle and the temperture of two phase is nearly equal at middle - top part
模擬結果表明,由於原料油射流的影響,提升管反應器內催化劑顆粒的流動特徵非常復雜,在噴嘴附近的催化劑顆粒存在明顯的滑落返混;裂化產物濃度沿提升管存在非均勻分佈;氣粒兩相間溫差在噴嘴附近顯著,在中上部氣粒兩相溫度幾乎相等。 -
Measures to prolong life time of fuel injection nozzle couple parts for diesel engine
延長柴油機噴油嘴偶件使用壽命的措施 -
Diesel engines - screw - in injection nozzle holders, types 20, 21, 21. 1 and 27 for pintle nozzle size ' s1 ' type ' b '
柴油發動機. s1規格b型針栓式噴嘴的20 21 21 . 1和27型擰入式噴嘴固定器 -
Road vehicles ; screw - in injection nozzle holders types 20, 21 and 27 for pintle nozzle size " s ", type " b " ; identical with iso 7026 : 1990
道路車輛. b類s規格的針式噴嘴用的20 21和27型螺絲擰 -
Diesel engines - screw - in injection nozzle holders, types 20, 21, 21. 1 and 27 for pintle nozzle size " s ", type " b "
道路車輛.型號b規格s軸針式噴油嘴用型號為20 21 21 . 1和27的旋入式噴油嘴座 -
Flanged - mounted injection nozzle holder
突緣安裝噴油器殼體 -
Under the classic automatically control theorist ' s leading, the thesis establishes idiographic practice methods that using closed loop open type numerical control system to reconstruct the old hydraulic injection nozzle center hole and inner cone grinder
在經典自動控制理論的指導下,制定了使用數控系統的全閉環控制方式來改造液壓中孔座面磨床的具體實施方案。 -
In the paper, it mainly discusses how through redevelopment technique on the homemade open type numerical control system to successfully reconstruct an old hydraulic injection nozzle center hole and inner cone grinder, and make this declining machine obtain excellent capability
本文主要論述了在利用即將報廢的液壓中孔座面磨床本體基礎上,使用國產開放型數控系統,經二次開發技術,成功地將其改造成性能優良的數控磨床的具體方法。
分享友人