interfacial adhesion 中文意思是什麼

interfacial adhesion 解釋
界面粘附
  • interfacial : adj. 1. 界面的，面際的。2. 界面角的。
  • adhesion : n. 1. 黏附，附著，膠著。2. 黏附力；黏附（現象）。3. 追隨；皈依；信奉；同意，加入。4. 【醫學】黏連（物）。
  1. Interfacial atoms diffusion or covalence by a circulated - argon ion bombardment process could improve the adhesion strength between the coatings and the uranium substrate

    循環氬離子轟擊鍍方法可促進使膜-基界面原子間的擴散或鍵合，有利於提高膜-基結合強度。
  2. Consequently, with increasing mmt content, the tensile strength and young ' s modulus of hdpe - g - aa / mmt nanocomposites increased, while that of hdpe / mmt composites decreased. moreover, the addition of mmt to hdpe - g - aa decreased the melting temperature and the degree of crystallization of the matrix. these changes may be attributed to high interfacial adhesion between hdpe - g - aa matrix and exfoliated clay, which reduces the mobility of crystallizable pe chain segments, and subsequently reduces the crystallization ability

    研究結果表明： mmt在hdpe中不能達到納米級分散，而在hdpe - g - aa中， mmt能以插層型利剝離型的結構存在，這主要是由於極性的丙烯酸接枝在hdpe上提高了後者的極性，而且能與mmt上的活性基團進行化學反應，從而提高了pe鏈進入mmt層間的可能性，使mmt在基體中達到納米級分散。
  3. The wood surface polarity is another important factor influencing the interfacial adhesion across the wood / plastics interface

    木材的表面極性（ y 。 』 ）是對木塑復合界面性能有影響的另一個重要因子。
  4. The results show that proper control the motion mode of the particle in plating results in many strengths of the nickel films, such as good uniformity, high compactness, and strong interfacial adhesion

    濺射鍍膜時，通過控制空心微珠的運動方式，在空心微珠表面沉積了一層均勻性好、附著力強和緻密性好的金屬鎳膜。
  5. The synthesis of modified polyolefin which grafted polar groups ， effects on interfacial adhesion of glassfiber reinforced polyolefin composite systerm and applications in glass fiber sizing were introduced in this paper

    本文介紹了接枝極性基團的改性聚烯烴的合成及其對玻璃纖維增強聚烯烴復合體系界面結合的影響以及在玻璃纖維浸潤劑配方中的應用。
  6. In addition, a new analytical method was used to solve the shear strength of the fiber / epoxy interface. the result showed good agreement with that from the kelly - tyson equation. meanwhile, according to the sfc tests of the single fiber reinforced epoxy matrix composites treated by four types of surface treatments, the interfacial adhesion conditions were estimated by critical fiber length, interfacial shear strength and single fiber microdamge mode

    此外，文中對單纖維復合材料斷裂實驗運用了新的解析方法，求解了玻璃纖維環氧復合材料界面的剪切強度，與kelly - tyson等式方法求得的界面剪切強度有著很好的一致性；同時，對四種不同表面處理劑處理的單纖維復合材料斷裂實驗進行了分析，從臨界纖維長度、界面剪切強度和單纖維斷裂實驗中纖維斷點周圍基體形貌評價了界面的粘結情況。
  7. 2. effect of the viscosity ratio, mterfacial adhesion, processing conditions and composition on the dispersing morphology and properties of pp / eoc blends was investigated. low viscosity ratio and high shear rate during processing were found to produce fine and uniform dispersion of eoc in pp matrix, while low viscosity ratio, high interfacial interaction, good fluidity of elastomer and high shear rate in molding process resulted in fibril dispersion, which afford a guide for controlling the morphology of pp / eoc blends

    研究了粘度比、界面相互作用、加工條件和共混比例等因素對pp eoc體系分散形態和性能的影響，發現粘度比小和加工過程中剪切強度大有利於彈性體在基體中分散均勻細化；粘度比小、界面相互作用強、彈性體本身的流動性好及成型時受到的剪切應力大，使彈性體相易變形，沿流動方向取向呈纖，闡明了各因素對形態影響的作用機制，這對pp eoc共混物的形態控制具有重要的指導作用。
分享友人
分享到 Line

分享到臉書