internal air temperature 中文意思是什麼

internal air temperature 解釋
內氣溫
  • internal : adj 1 內的，內部的 （opp external）。2 國內的，內政的。3 體內的，內服的。4 內在的，本質上的，固有...
  • air : n 1 空氣，大氣。2 天空，空中。3 微風，和風。4 態度，樣子，風度，氣派；〈pl 〉高傲的架子。5 傳播，...
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. Our company relay on abundant technique, advanced produce appliance and modern managerment mode, our products have good quality and function. the company has been iso9001 : 2000 quality system sgrant can b015 - q : 15 03q5439r10, has international facture calculate appliance s lisense cmc zhejiang province 02810232. the company alse strictly produce, sale and service according to the quality system. main products : almighty putin intelligent temperature control meter xmt - 808, can put through the computer and has the appearance, program intelligent industries adjustment meter, record meter, a series of temperature and humidity controller xmt - 9007, voltage adjustment instruments zk - 1, zk - 3, all kings of temperature sensors, time relays, lcd and so on. wide make use of the plastics, packing, printing, house electric appliance and some other machine field. also include the textile printing, chemical engineering sprint, dyeing, baccy, even, air conditioner, make cold and etc. field. has variety of products, all standards and directly sales to internal and international market

    主要產品有萬能輸入型智能溫度控制儀表xmt808 ，具有計算機通訊介面及界面可編程智能工業控制儀記錄儀，溫濕度控制儀表xmt9007整套，電壓調整器zk - 1 zk - 3 ，各類溫度傳感器，時間繼電器，液晶顯示儀表等產品品種多，規格全，真接銷往國內及國際市場，廣泛應用於塑料包裝食品印刷家電等機械行業和輕紡化工印染煙草烘箱空調製冷等領域。
  2. Automotive air conditioner accessories : automotive air conditioner cooler, evaporator, heat sink, air conditioner, temperature adjuster, heater, central cooler, air desiccators, cooling fan controller, internal heat exchanger, compressor, motor, air warmer, warm air device, electronic fan for cooling condenser, liquid can, thermal expansion valve, air condition pipeline, switch, clutch, connector, height valve, shunt valve and all kinds of automotive air conditioner production materials ( body aluminum, copper materials, etc ), production equipment, measurement equipment, etc

    車用空調配件：各種車用空調冷凝器、蒸發器、散熱器、空調器、調溫器、加熱器、中冷器、空氣乾燥器、冷卻風扇控制器、內部熱交換器、壓縮機、電動機、暖風機、暖風裝置、各種冷凝器電子扇、貯液灌、熱力膨脹閥；各種車用空調管路、開關、離合器、接頭、高低閥、換向閥及各種車用空調生產材料（車用鋁材、銅材等） 、生產設備、檢測設備等。
  3. The experimental results indicate that when the air flow rate is determined, the key problem for energy saving is how to keep the indoor thermal comfort at a suitable level and reduce the difference between the internal and external temperature of the room. a formula is gained for calculating the critical values of air exchange rate. when ventilating rate is greater than the value, radiating heating is the better way for energy saving, or else, convection method in heating is more suitable

    實測還指出，當通風量一定時，如何保證人體熱舒適度不變而減少室內外氣溫差將成為大通風量房間節約採暖能耗的關鍵，本文結合圍護結構傳熱機理，在對三種方式的能耗狀況進行理論分析的基礎上，提出了換氣次數的節能臨界值，若換氣次數高於此值，則輻射供暖是較好的選擇，否則，散熱器供暖是較好的方法。
  4. The analysis indicates that temperature change can fall into three successive phases ( temperature rising fast, temperature stabilization and temperature rising slowly ) ; internal pressure is composed of vapor pressure and air pressure

    分析表明：板坯內部的溫度變化分為3個階段，即快速升溫階段、溫度穩定階段和後期的慢速升溫階段；內部氣壓由水蒸氣分壓和空氣分壓組成。
  5. I set up the mathematics model of heat transfer of the thermal bridge of the building and utilize numerical method to analysis whether occur condensation problem on the internal surface in the thermal bridge or not. through the analysis and studying of this subject, we can make conclusion as followed : because the internal surface of the bared wall body incline to be lower than the air dew point indoor, which apt to dew, with the reducing of out air temperature and increasing of the air temperature indoor

    另外，通過建立建築熱橋的傳熱數學模型，利用數值求解的方法，分析了外墻熱橋部位內表面是否結露的問題，研究得出裸露墻體內表面極易低於露點溫度而結露，並且隨著室外溫度的降低，室內溫度越高，外墻熱橋部位的內表面越容易結露。
  6. The engine is tested on the dynometer using the software that can monitor the ecu ( electronic control unit ) internal dataflow. and the electronic control fuel injection system parameters ( e. g. position of throttle valve, engine speed, air temperature, engine temperature, duration of injection ) are acquired at many different working conditions of engine

    本文以hirth3203二沖程汽油發動機為研究對象，利用開發的ecu內部動態數據流監測軟體進行發動機臺架試驗，獲取了在不同的油門開度和轉速下電控燃油噴射系統的一系列工作參數，如節氣門開度、發動機轉速、進氣溫度、氣缸溫度、蓄電池電壓以及噴油脈寬。
分享友人
分享到 Line

分享到臉書