joints 中文意思是什麼

joints 解釋
綱線的交織
  1. In this paper, ackerman steering linkage of double - wishbone suspension is taken as the study object, choosing the splitting joint and steering lever joint to carry out the design of optimization the mathematics models are established based on the multi - body system dynamics, applying its analysis method of kinematics to study the mechanism kinetic principles owing to more spatial factors considered, and calling off many hypotheses affecting the accuracy, compared with the traditional methods, the models are better to reflect the realistic motion principles, the results are more exact and applicable moreover, the force analysis is applied to the conduct mechanism the analysis method of dynamics in the multi - body dynamics is applied to study the forces applied on every component, working out the constraint reaction force of up and down ball joints, and developing the current computation program in the end, produce the upper wishbone geometry model in the ansys software package, meshing and carrying out the fea, testifying if the intensity of the wishbone meet with the requirements

    本文以雙橫臂獨立懸架的轉向傳動機構作為研究對象，選擇對斷開點和節臂球銷的位置進行優化設計，在此基礎上建立了基於多體系統動力學的導向機構和轉向傳動機構的數學模型，運用該學科的運動學分析方法研究機構的運動規律，編制了通用優化設計軟體。由於考慮了更多的空間因素，取消許多影響準確性的假設，因此建立的數學模型與傳統的方法相比更能反映實際運動規律，得到的優化結果也更加精確實用。此外，本文還針對導向機構進行受力分析，在建立該機構的空間動力學模型后，運用多體動力學中的動力學分析方法研究各個桿件的受力，計算出上下球鉸的約束反力，並開發出了相應的通用計算程序。
  2. In foretime, the adscription of area before railway stations is somewhat vague, as it locates on the joints of railway department and the local government, it makes this area a vague one in administration

    過去，車站站前的歸屬比較模糊，處于鐵路與地方政府管理范圍的交界區域，從而造成了管理上的模糊地帶。
  3. Joints stiffen with advancing years.

    人一上年紀，關節就變僵硬了。
  4. Sensors were fitted to the knee and ankle joints of lower - limb amputees

    下肢截肢者則在其膝關節和踝關節設有傳感器。
  5. Upper - limb amputees were fitted with a special data glove and had sensors attached to the elbow and wrist joints

    上肢截肢者戴上一個特殊的數據手套，在其肘關節和腕關節連接有傳感器。
  6. The coronal approach provides wide exposure of surgical field when approaching the bilateral joints and developing the temporalis fascial flap for disc replacement. a case of ankylosing spondylitis with multiple joints ankylosis utilizing coronal approach in replacement of bilateral tmj was reported

    本文報告一僵直性脊椎炎造成全身多處關節黏連，包括兩側顳顎關節黏連的病例，應用冠狀切開術施行兩人工顎關節置換術，獲致令人滿意的結果。
  7. Based on the analysis of mechanism for joint region, the " frame - wall " and " aslope compression stub column " mechanical models and yielding patterns of core zone of the joints are set up. the shear load - carrying formulation for joint core zone is also given in terms of plastic ultimate analysis. and then, the comparisons between the formulas given in this paper and that of chinese design code ( draft ) and nonlinear fem as well are presented

    對節點核心區的抗剪，通過受力機理的分析，建立了鋼「框架剪力墻」加混凝土「斜壓短受力體系及其屈服機制，根據塑性極限分析，給出了節點核心區抗剪承載力計算的迭加公式， 《規程》公式和非線性有限元近似模擬分析結果進行了比較。
  8. Standard specification for asphaltic plug joints for bridges

    橋梁瀝青塞接頭的標準規范
  9. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。
  10. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  11. Its behaviour is dominated by discontinuities such as faults, joints and bedding planes.

    它的性態是由像斷層、節理和層面等這樣一類不連續面控制的。
  12. According to specificities for jointed rock mass, multiple sliding failure of a jointed rock mass is presented, due to accumulation of stress along bedded plane of rock mass and destruction of remnant intact rock bridges between bedded planes and joints

    摘要針對節理化巖體的自身特點，提出沿巖體層面產生的應力集中以及層面與節理之間的殘餘完整巖橋破壞，將可能導致巖體產生復合式滑移破壞。
  13. And rock triaxial serve testing system is used, through model test involving bedded planes and a set of joint normal to the bedded planes in rock mass, multiple sliding failure affected by properties of joints and confining pressure is analysed, the condition triggering multiple sliding failure and characteristics of failure plane are given, under the co - action of inclination of connective joints ( bedded planes ), interlocking conditions of critical joints and confining pressure

    並在室內利用巖石三軸剛性伺服機，通過模型試驗對巖體的層面和一組與層面正交的節理的情況進行模擬研究，分析了結構面性狀和圍壓對復合式滑移破壞的影響，給出了在貫通性結構面（層面）傾角、非貫通性結構面以及圍壓等因素共同作用下，節理化巖體發生復合式滑移破壞的條件以及破壞面特徵。
  14. Stability of rock slopes is generally controlled by the structure of rock masses, especially the soft structure surfaces. analysis of rock mass structures is a key to establish geological models and numerical simulation and a foundation to assess the stability of rock slopes. the weak structure surfaces are mainly bedding planes, faults, joints, schistosity plane and contact zones of intrusive bodies. since they are different in genesis and scale, the rock masses are different in features and mechanical intensities. based on the combination of rock structure bodies, 15 basic modes of deformation and failure of rock slope are systematically summarized. the deformation and failure of rock masses actually result from the recombination and rearrangement of these rock bodies. there are 11 types of rock mass structures and various deformation and failure of bank slopes are present in the reservoir area of the three gorge project

    巖體結構，特別是軟弱結構面對基巖斜坡變形與破壞具有顯著的控製作用，巖體結構模式分析是建立斜坡地質模型和數學模型的關鍵和評價斜坡穩定性的基礎。巖層層面斷裂構造節理裂隙片理與劈理以及侵入體和圍巖的接觸帶等是控制基巖斜坡穩定的軟弱結構面，這些成因不同大小不一的結構面將巖體分割成性質各異力學強度不均的各種巖體結構體，構成了15種基巖斜坡變形破壞的巖體結構基本模式。不同結構體的重新組合與排列是斜坡失穩的內在原因。
  15. It can produce pressure on the skin, especially over bony prominences and joints.

    它會壓迫皮膚，尤其是骨的突起和關節處的皮膚。
  16. The hill, shaped with the weathering and eroding along the plumb joints of the granodiorites which formed about 2. 7 billion years ago, is like buddha palm especially verisimilitude in green bosk

    佛掌山為27億年左右形成的花崗閃長巖，沿垂直節理風化剝蝕后形成奇特的佛掌型山，在綠樹叢中尤顯逼真。
  17. Railway transport equipment. clevis and tenon joints. inner brass rings type bs

    鐵路運輸設備. u形環和榫接頭.型銅制內環
  18. Brazing - guidance on the application of brazed joints

    銅焊.銅焊接合的應用指南
  19. Brazing - non - destructive examination of brazed joints

    釬焊.硬釬焊接頭的無損檢驗
  20. Methods of tensile test for butt welded joints

    對焊焊縫抗拉伸試驗方法
分享友人
分享到 Line

分享到臉書