junction efficiency 中文意思是什麼

junction efficiency 解釋
中繼效率。

  • junction : n. 1. 接合，連接，連絡。2. 接合點，交叉點，（河流的）匯合處，（鐵道的）聯軌點。3. 【電學】中繼線。4. 【物理學】接頭，結。
  • efficiency : n. 1. 功效。2. 效率；效能；實力，能力。3. 【物理學】性能。
  1. In the paper we mainly researched space gainp2 / gaas / ge high efficiency tandem cells " making process by home - made low pressure mocvd technology and new solar concentrators. firstly, we presented reseached and development of solar cells in china and foreign countries ; secondly, on the basis of fundamental priciples and theories, we discussed some factors of influcing conversion efficiency of solar cells, and analysed the i - v output feature of two - junction tandem cells ; then the design concept of gainp2 / gaas / ge two - junction tandem cells was discussed, the detailed aspects of gainp2 / gaas / ge tandem cells epitaxy growth by low pressure mocvd was studied, and some questions on epitaxy growth ( such as crystal qualities, interface stress, element interdiffusion, n - and p - type doping et all ) were solved ; after that, the cell fabrication process was described ; finally, we reseached the hot pressing and mould process technology of an arched line - focus fresnel lens made by pmma, designed and fixed new solar concentrators

    本文致力於用自製的低壓mocvd裝置進行cainp _ 2 / gaas / ge空間用高效級聯太陽能電池製作的工藝以及聚光太陽能電池組件的研究。首先，介紹了國內外太陽能電池的研究現狀及應用情況；其次，運用太陽能電池基本原理討論影響電池轉換效率的因素，分析了級聯電池的伏安特性；隨后，討論了cainp _ 2 / gaas / ge雙結級聯電池的結構設計理念，研究了採用低壓mocvd技術生長cainp _ 2 / gaas / ge級聯太陽電池材料的工藝過程，解決了異質材料生長的結晶質量、界面應力、材料互擴散以及材料n 、 p型摻雜等一系列問題；然後總結了級聯電池的后工藝製作；最後，研究了以pmma為材料的菲涅耳線聚焦透鏡的熱壓成型工藝及其模具的加工工藝，設計並安裝完成新型聚光太陽能電池組件。
  2. At the initial stage of planar technique, b was employed as ideal diffusion impurity in base - region of npn si planar devices because of the match of its solid - solubility and diffusion coefficient in si with those of p in emission - region, and the good shield effect of sio2 film to b. but because of the relatively large solubility ( 5 1020 / cm3 at 1000 ) and the small diffusion coefficient, the linear slowly - changed distribution of acceptor b in pn junction can not be formed, which could not cater to the requirement of high - reversal - voltage devics. thereafter b - a1 paste - layer diffusion technology and close - tube ga - diffusion technology had been developed, while the former can lead to relatively large the base - region deviation and abruptly varied region in si, which caused severe decentralization of current amplification parameter, bad thermal stability and high tr ; the latter needed the relatively difficult pack technique, with poor repeatability, high rejection ratio, and poor diffusion quality and productio n efficiency

    在平面工藝初期，由於b在硅中的固溶度、擴散系數與n型發射區的磷相匹配， sio _ 2對其又有良好的掩蔽作用，早被選為npn硅平面器件的理想基區擴散源，但b在硅中的固溶度大（ 1000時達到5 10 ~ （ 20 ） ，擴散系數小， b在硅中的雜質分佈不易形成pn結中雜質的線性緩變分佈，導致器件不能滿足高反壓的要求，隨之又出現了硼鋁塗層擴散工藝和閉管擴鎵工藝，前者會引起較大的基區偏差，雜質在硅內存在突變區域，導致放大系數分散嚴重，下降時間t _ f值較高，熱穩定性差；後者需要難度較大的真空封管技術，工藝重復性差，報廢率高，在擴散質量、生產效率諸方面均不能令人滿意。
  3. The high efficiency and high power semiconductor laser with multi - active regions, which are cascaded by reverse biased tunnel junction ( s ) can resolve the problems in theory and overcome these shortcomings

    通過反向偏置隧道結將多個有源區再生耦合級聯起來的新型高效大功率半導體激光器從理論和實踐上解決了傳統激光器存在的上述問題。
  4. Graded doping is adopted in both sides of the junction ( double graded doping ). this results in a strong ( drift ) electric field throughout the whole active layer. this field will accumulate minority carriers effectively and the whole internal quantum efficiency is increased

    漂移場的形成是通過mbe技術，在結的兩側都採用梯度摻雜（即雙梯度摻雜） ，從而在整個有源層都建立起一個強的（漂移）電場，有效地利用載流子在電場作用下的漂移作用收集少數載流子，使得總內量子效率得以提高。
  5. The aim of the project is to enhance the operational efficiency and safety of the light rail system as well as road traffic at the junction

    工程旨在提升輕鐵及路面交匯處的運作效率及安全水平。
分享友人
分享到 Line

分享到臉書