key load 中文意思是什麼
key load
解釋
鍵帶信息輸入-
In the dissertation ' s chapter 3 to chapter 5, the mechanical and physical performances of the engineering plastics are analyzed, the failure mode and the designing computing methods of engineering plastics member suffering the static load, dynamic load, impact load, pulse load, are studied. by the practice application and ball firing experiment of the engineering plastics key piece in the weapons, the precious experiences, for engineering plastics application and confirmation of the material performances guideline in the weapons, are obtained
論文的第三章至第五章，分析了工程塑料物理機械性能，研究了受靜載荷、動載荷、沖擊載荷及脈沖載荷下工程塑料構件的失效模式和設計計算方法，通過工程塑料在槍械關鍵受力結構件上的實際應用和實彈射擊試驗，取得了寶貴的經驗，為高性能工程塑料在槍械上的應用和材料性能指標的確定奠定了基礎。 -
For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization
其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。 -
The key products of the company are high alumina brick, fireclay brick, phosphate - bonded wearable brick, exfoliation - resistant high alumina brick, high refractoriness under load brick, corundum brick, magnesite brick, magnesite ? chrome brick, series of corundum, sic furnace chamber and pipe, ceramisite brick, corundum - mullite brick, corundum - chrome brick, sillimanite brick, magnesite alumina spinel brick, acid - resistant brick, alkali - resistant brick, zirconia - corundum brick, alumina bubble products, series thermal insulating refractory products, high alumina castable, corundum castable, corundum ramming, brown - corundunm castable, sic castable, low - cement castable, alkali ? resistant castable, light silica alumina products, stainless steel fibre reinforced castable, etc
主要產品有：高鋁質磚、粘土質磚、磷酸鹽耐磨磚、抗剝落磚、高荷軟磚、剛玉磚、碳化硅磚、鎂磚、鎂鉻磚、各種剛玉、 sic爐膛、爐管製品、陶粒磚、剛玉莫來石磚、鉻剛玉磚、硅線石磚、鎂鉻尖晶石磚、耐酸磚、耐堿磚、鋯剛玉磚、氧化鋁空心球製品及各種輕質保溫材料、高鋁質澆注料和剛玉澆注料、搗打料、棕剛玉澆注料、碳化硅澆注料，低水泥澆注料、抗堿性澆注料、輕質硅酸鋁製品、鋼纖維增強澆注料等80餘種系列耐火材料。 -
Anchor hook key bearing load observation system
錨鉤銷軸載荷監測系統。 -
Some key issues in the modeling of a long span composite cable - stayed bridge are discussed such as cable tension, dead load, large deflection, concrete deck stiffness, concrete deck - steel girder connection, and boundary condition. some conclusion can drawn from the thesis : 1. the initial equilibrium configuration of the bridge is clarified in the thesis
本文深入討論大跨度結合梁斜拉橋"基準"有限元模型建立過程中的幾個關鍵問題並得到一些有意義的結論： 1 .明確斜拉橋在索初應力和恆載作用下的初始平衡構型? ?處于初始平衡狀態時的幾何位置，給出了其計算方法。 -
The effect of overburden separation dynamic development under key stratum on grouting for bed separation space was analyzed, in order to deal with the problem that the current bed separation growing technology can not prevent the key stratum from breakage, put forward the isolated section - grouting technology for overburden bed separation space, integrated the virtue of growing for bed separation space and partial extraction, the bed separation grouting bodies, key stratum and isolated section pillars were made to constitute the load - carrying body all together, and to reach the purpose of reducing subsidence effectively, increase the coal seam extraction ratio, and accelerate the development of isolated section - growing technology for overburden bed separation space
摘要分析了關鍵層下離層動態發育對離層充填的影響，針對目前離層區充填工藝不能阻止覆巖關鍵層初次破斷的問題，提出了「覆巖離層分區隔離注漿充填」技術，它綜合離層充填與條帶開采技術的優點，通過離層區充填置換或減小分區隔離煤柱寬度，使「離層區充填體關鍵層分區隔離煤柱」形成共同承載體，從而達到有效減緩地面沉降的目的，提高了煤層采出率，促進了覆巖離層充填減沉技術的發展。 -
The fifth part introduces the key technique of the whole system : four - layer switch, load balance and ssl security and acceleration
第五章介紹了在整個系統設計中採用的關鍵技術，主要包括：四層交換、服務器負載均衡和ssl安全及加速。 -
An advanced software platform with the parameter identification as its core has been developed for load modeling. this software platform has been practiced in the engineering project of load modeling for zhangjiakou area, as well as the national power grid key project of load modeling for the north east of china
基於論文所建立的理論，已開發了以參數辨識為基礎的系統的負荷建模軟體平臺，基於該軟體平臺先後完成了張家口地區電網負荷特性建模和東北電網負荷建模工作。 -
Based on the theoretical analysis and design practice in successful development of allway desiel engine in china, the design concepts of key parts and components of engine, in particular the cylinder block and cylinder head, are analyzed for meeting the requirements for high performance and low emission as well as normal and reliable operation of diesel engine for medium and heavy commercial vehicle under high combustion pressure and high thermal load
摘要結合我國自主開發的「奧威」發動機在設計工作中的理論分析與實踐，就低排放中重型商用車柴油機在開發工作中為滿足高性能、低排放的要求及在高燃燒爆發壓力和高熱負荷下正常可靠地工作，對發動機的關鍵零部件，尤其是缸蓋與缸體的設計概念進行了分析。 -
Technology and key craft of high - temperature strain gauge load cell
高溫應變式稱重傳感器技術與關鍵工藝 -
Technology and key craft of high - temperature strain gauge load cell receive last issue
高溫應變式稱重傳感器技術與關鍵工藝接上期 -
The researches including discharge capacity, pressare properties, cavitation characteristics at some key positions, hoisting load of the gate, configuration of energy dissipator at the exit dentated - sill, and downstream scouring were performed by hydraulic model tests
藉助系列水工模型試驗對水布埡放空洞的泄流能力、壓力特性及關鍵部位的空化特性、閘門啟閉力、出口鼻坎消能工體型及下游沖刷等進行了較深入的研究、分析。 -
In order to implement an energy - saving method which keeps iron loss equal to copper loss using variable - voltage in light load, induction motor parameter identification at any moment is a key problem
對于輕載調壓使銅損等於鐵損的這一節能方法而言，在線辨識出電機的參數是一個關鍵點。 -
Port crane is the main load and unload equipment in port, how good the manipulator ' s skill is the key factor in determine the safety, efficiency, durable and profit of using the equipment
港口起重機是港口裝卸貨物的主要設備，操作人員的技術熟練程度對港口生產安全、設備使用效率、使用壽命及經濟效益起著決過定性的作用。 -
( 4 ) the intelligent inspect system for roof latticed truss structure in shenzhen citizen center is selected as a practice background, and the intelligent inspect method to the steel bracket of roof truss is researched in present paper, in which includes several tasks as follows : automatic load identification for bracket based on neural network method, prompt calculation for the stress of key points on bracket, and its service status evaluation and stress alarm
（ 4 ）以深圳市市民中心屋頂網架結構的智能監測系統為實際應用背景，詳細介紹了網架結構支撐鋼牛腿的智能化監測方法。其中包括，基於神經網路的牛腿瞬時荷載的自動識別、牛腿關鍵點應力的快速正向計算、以及關鍵點工作狀態的評估與報警。 -
Using displacement - load sensor to collect displacement and load data and adopting micro - power wireless communication module to transmit the load and displacement data to main part of the oil - well monitor and control system by serial port to form the indicator diagrams. the key to give the oil well effective monitor and control is monitoring the data of the indicator diagrams
通過固定在抽油桿上的位移-載荷傳感器實時採集油桿的位移數據和載荷數據，再採用微功率無線通信模塊通過串口將採集來的位移數據和載荷數據傳送至遠端的監控系統主機，用兩種數據形成示功圖曲線。 -
Considering that the characteristics of our country ' s highway tunnels are always of long spans, tabular and of various geometry, by means of thorough analysis of the different problems existed in the design of support structures of the tunnels at present, this paper pays special attention to the two key problems, optimization method of form selection of structural section of the tunnel as well as the stability and bearing capacity of the support structures, in the design of the long and large tunnel on high - class highway, introduces the simplified complex - form optimum method in the structure optimization theory, discusses the optimum design model of lining section of highway tunnel with satisfying demands in building clearance, ventilation and load conditions, puts forward an optimization method of form selection of three different kinds of lining sectional forms ( i. e. single - center circle, three - center tabular circle and three - center sharp circle ), establishes a complete set of systematic optimum design the ory and method of long and large tunnel on high - class highway, develops the corresponding computer software used on the planned xuefeng mountain highway tunnel on shaoyang to huaihua expressway in hunan province for optimization of form selections of the structural sections, and obtains a series of relatively reasonable structural design parameters
本文針對我國公路隧道多為大跨度、扁平、幾何形狀呈多樣化的特點，通過深入分析目前隧道支護結構設計中存在的各種問題，抓住高等級公路長大隧道設計中隧道結構斷面的優化選型及隧道支護結構的穩定性與承載能力兩個核心問題，引入結構優化理論中的簡易復合形優化方法，深入探討了滿足建築限界、通風條件、受力狀態約束等條件下公路隧道襯砌斷面優化設計模型，提出了三種襯砌斷面形狀（單心圓、坦三心圓和尖三心圓）的優化選型方法，建立起一套完善的高等級公路長大隧道的系統優化設計理論與方法，並開發出相應的計算機程序，用於擬建的上海至瑞麗國道主幹線湖南省邵陽至懷化高速公路雪峰山長大高速公路隧道的結構斷面優化選型，得出了一系列較為合理的支護結構設計參數。 -
In accordance with the occurrence behavior of roof strata and the fracture characteristics of key stratum in shallow seam longwall mining, studied post - buckling behavior of roof key stratum in the process of mining by using initial post - buckling theory, which derived a critical load and a breaking span of the main roof during the first weighting, determined the final subsidence and the maximum rotation angle for broken key stratum, and presented an application with the example of daliuta 1203 face
摘要根據淺埋煤層頂板巖層的賦存特點和長壁開采時關鍵層的變形破斷特徵，應用初始后屈曲理論探討了開采過程中頂板關鍵層的后屈曲性態，得出了老頂初次來壓時頂板的臨界載荷和破斷步距，確定了頂板破斷后的極限下沉量和回轉角，並以神東礦區大柳塔1203工作面為例給出了工程實例。 -
Based on the accumulated engineering experience of cfb technology by tsinghua university, this paper develops a pseudo - static model to study the performance of a real 135mw cfb reheating boiler under partial load. this model is a semi - theoretical model in which some key parameters are according to the engineering experiences accumulated by department of thermal engineering, tsinghua university in the last fifteen years
本文在國內外已有研究成果基礎上，尤其是根據清華大學熱能工程系多年來致力於流化床燃煤技術的研究與開發所積累的豐富的工程經驗，採用準靜態模型化方法，對135mw再熱循環流化床鍋爐的部分負荷性能進行了研究。 -
In 2004, the company s technology development department has actively and successfully developed the shield - type american - style european - style cable heads, high - low - voltage cable branch cases for load switch busbar coupler system, outdoor ring network cabinets, box - type transformer substations and auxiliary products, which have passed the authentication one after another and been launched into the market in large batches, giving a strong support to the upgrading of the national urban power grids and the construction of key projects ; in 2006, the company has developed the four - splitting and dual - splitting wire and cable box and released to market ; the 2nd half of 2006, over 500kv ultra - high voltage electrical hardware being developed for 2007 market ; four products awarded national patents in 2006
2004年公司技術開發部積極開發了屏蔽型美式歐式電纜接頭，負荷開關母線聯接系統的高低壓電纜分接箱，戶外環網櫃，箱式變電站及配套產品相繼通過鑒定，大批量投入市場，有力支持國家城網改造與重大工程建設2006年公司又研製出四分流二分流電線電纜分線盒，已投放市場2006年下半年，正在研製開發超高壓500kv及以上電力金具，有望2007年投放市場2006年有六種產品已申請國家專利。
分享友人