length of tolerance 中文意思是什麼
length of tolerance
解釋
長度允差-
Tolerance of chain contact pitch and chain length in the new edaphic and mineral chain ditcher
刀式礦土復合型鏈條接觸節距及鏈長公差的研究 -
The paper will study the upper questions based on the two interconnection networks. first, we give a fault - tolerant routing algorithm under the connectivity of the crossed cube in o ( n ) time and the length of the longest routing path ; second, with the rapid progress in vlsi, the failing probability of processors and links is very low, the traditional connectivity underestimates the resilience of large networks / here by applying the concept " conditional connectivity " introduce by harary, we show that the n - crossed cube can tolerate up to 2n - 3 ( n > 2 ) processors failure and remain connected provide that all the neighbors of each processor do not ' fail at the same time, the result is the same as the hypercube. we also give a related algorithm in o ( n ) time, and the length of the longest path ; third, we apply cluster faun tolerance introduced by q. - p
根據menger定理， n -維交叉立方體可以容納n - 1個故障頂點，我們給出了它的時間復雜度為o （ n ）的容錯路由選擇演算法及其最長路徑長度分析；在此基礎上本文證明， n -維交叉立方體的條件連通度為2n - 2 （ n 2 ） ，並給出了相應時間復雜度為o （ n ）的演算法及其最長路徑長度；除此之外，本文還證明當n -維交叉立方體中的故障簇個數不大於n - 1 ，其直徑不大於1 ，故障頂點總數不超過2n - 3 （ n 2 ）時，交叉立方體中任兩個無故障頂點都至少有一條可靠路徑。 -
The analysis of precision about mould - cut main mechanism with clearances is advanced. on the basis of analysis of slider displacement error influenced by the crank length tolerance, the coupler length tolerance and clearances in revolute joints for mould - cut main mechanism, some reasonable suggestions about tolerance distribution of bars length and fitting precision of joints are put forward
考慮運動副間隙對主切機構進行了精度分析，通過分析主切機構中各桿長誤差和運動副間隙對滑塊位移誤差的影響，對商標模切機設計初期桿長誤差分配和運動副間隙配合精度提出了合理的建議。 -
This interpolation module uses the popular and advanced nurbs interpolation technology. the procedures of math processing for nurbs, preprocessing for interpolation and real - time interpolating running on dsp are presented in this article. the interpolating procedure uses an advanced self - adjusting interpolation method, which can automatically adjust the length of interpolation according to machining speed, acceleration and the tolerance of bow height
插補模塊則採用了當今最流行最先進的nurbs插補技術，設計了nurbs數學處理程序，插補預處理程序，運行於dsp的實時插補程序，該插補軟體採用了先進的自適應插補方法，可以根據加工的速度，加速度，弓高誤差的要求自適應調整插補步長，同時採用了對插補點的預估演算法，免去以往加工方法中求導的運算，大大降低了運算量，提高了加工速度。 -
There existed very significant correlations between drought tolerance and relative values of root dry weight, total root length, and root volume ( per plant dry weight basis ), respectively, which could be used as root indicators of drought tolerance
比根干重、比總根長、比根體積與耐旱隸屬函數平均值均呈極顯著正相關，可作為耐旱性的根系性狀指標。 -
As concentration of salt solution increased, the vigor index, germination index and the length of shoot and radical gradually decreased. the radicle was sensitive to salt stress and had low tolerance. it can be concluded that p. hendersonii has high salt tolerance, h. strobilaceum has low salt tolerance
隨著鹽溶液濃度的升高，大葉白麻和鹽節木種子的活力指數和發芽指數下降，幼芽和幼根的長度逐漸變短，幼根對鹽分脅迫敏感，忍耐力不強。 -
Automatic correct the tolerance : if you input the actual value it can reach automatically correct the tolerance of length, opposite angle line, snapping position and glass plate falling position
誤差自動校正：對板長誤差.對角線誤差.掰斷位置誤差及落板下落位置誤差，只要輸入實際值，可實現一次性自動校正。 -
The maximum working speed of the manufacture line is 10m min. the length tolerance is 0. 5mm, diagonal line tolerance is 0. 8mm, the feeding frame can be set as per customer s requirement. de - coiler - material feed - leveler grooving roller - shear
該生產線最大工作速度為10米分，精度為：長度誤差0 . 5mm m ，對角線誤差為0 . 8mm m ，上料架可以根據客戶要求配套。 -
Living example of design shows that reasonable designed manufacturing tolerance of bar length of four bar linkage could make the mechanism not only satisfy the requirement of accuracy but also lower the manufacturing cost
設計實例說明，合理設計四桿機構桿長製造公差，可使機構既滿足精度要求又降低製造成本。
分享友人