light gauge 中文意思是什麼
light gauge
解釋
小型量規-
Packaging - light - gauge metal packaging - open - top round cans defined by their nominal gross - lidded capacity
包裝.輕型金屬包裝.由標稱容量限定的圓形敞口容器 -
Light - gauge metal containers - round open - top cans - cans defined by their nominal gross lidded capacities
小型量規金屬容器.圓形頂部開口罐.由標稱加蓋總容量定義的罐 -
Packaging - light - gauge metal packaging - open top round cans defined by their nominal gross - lidded capacity ; german version en 13027 : 2001
包裝.小型金屬包裝.根據標稱總裝蓋容量定義的頂開口 -
Packaging - light gauge metal containers - aperture for plug - in rel plastic closures
包裝.輕型金屬測量容器.插入式rel塑封閉裝置的孔徑 -
Light gauge metal containers - three - piece necked - in tinplate aerosol cans - dimensions of the top end
小型量規金屬容器.三件式向內彎曲馬口鐵氣溶膠罐.頂端尺寸 -
Application of light - gauge steel structure in engineering practice
輕型鋼結構在工程實踐中的應用 -
Comparative analysis of mechanical behavior of light gauge steel structure
輕鋼龍骨結構體系受力性能的比較分析 -
Experimental research on lateral force resistance of light - gauge steel compound wall
輕鋼龍骨復合墻體抗側性能試驗研究 -
Researches on nafc and lcfc plates and their screw connections with light - gauge steel members
板及其與輕鋼龍骨自攻螺栓連接性能 -
Light gauge steel
輕量型鋼 -
Experimental research on truss beam carrying capacities of new type of light - gauge steel system
新型輕鋼龍骨體系桁架梁承載力試驗研究 -
Light gauge metal containers - definitions and determination of dimensions and capacities - part 2 : general use containers iso 90 - 2 : 1997 ; german version en iso 90 - 2 : 1999
薄板金屬容器.定義和測定尺寸及容量的方法.第2部分 -
Light gauge metal containers - round vent - hole cans with soldered ends for milk and milk products - capacities and related diameters
薄壁金屬容器.裝牛奶和牛奶製品用帶焊封埠的圓形通氣孔罐.容積和相關尺寸 -
Welded light gauge h steels for general structures
一般結構用工字型輕型焊接鋼材 -
Light gauge stainless steel tubes for ordinary piping
普通管路用輕型不銹鋼鋼管 -
Light - gauge metal containers - round open - top cans - internal diameters
小斷面金屬容器.敞口式圓形罐頭.內徑 -
The high frequency welded light gauge h sections for construction
結構用高頻焊接薄壁h型鋼 -
Thirdly, to improve the application of light gauge steel structure in our country, some experimentations of institute of new - style steel structure which adopting native productions are induced nally, three - dimensional finite element model is presented. compared with the tests, mumerical results are verified much accurate and efficient, therefore a reliable way is provided to utilize the computational technique adequately to reduce the tests and to utilize the experimental results adequately to improve design quality, ( 3 ) study on floor system. not only adequate strength, stiffness and integer stabilization must be provided, but also insulation, fire and acoustics must be satified
本文首先論述了lgsfcbw各種破壞模式及其原因,總結了各因素對lgsfcbw抗剪性能的影響,從而為我國引進和應用輕鋼龍骨結構體系奠定了基礎;其次從試驗模型、試驗方法和試驗結果三方面探討了國外lgsfcbw抗震性能的研究,並分析該體系的破壞模式和抗震特性、提出研究建議;然後介紹了為推動輕鋼龍骨住宅國產化,我們採用國產材料開展的系列試驗;最後提出了lgsfcbw的有限單元分析法,數值計算與試驗結果一致,為充分利用計算技術減少試驗數量和充分利用試驗成果提高設計水平提供了一條可靠途徑。 -
Concerning the tests, analyses, design and calculation of performances for light gauge steel framing, this paper focuses on following items : ( 1 ) the calculation of light gauge steel framed compound bearing walls ( lgsfcbw ) in compression and bending. based on north american specification and commentary for the design of cold - formed steel structural members, which was published by the american iron and steel institute, the detailed design requirements of wall stud assemblies are given considering the structural contribution of the attached sheathings and shear diaphragm is discussed briefly. then the calculational theoretic and method for sheathing braced wall stud assemblies complying with national code is brought up in compression and bending
本文圍繞輕鋼龍骨體系結構性能的試驗、分析、設計和計算,主要進行了以下四方面的研究工作: ( 1 )輕鋼龍骨復合承載墻體的受壓、受彎計算:以美國鋼鐵協會發行的北美冷成型鋼構件設計規范及其規范說明為依據,重點考慮罩面材料對墻龍骨設計的影響,給出了目前對承重墻龍骨設計的具體要求,並對剪力蒙皮進行了簡要討論;然後提出了符合我國規范術語的剪力蒙皮作用的輕鋼龍骨復合承載墻體(即罩面支撐墻龍骨)受壓、受彎的計算理論和方法;最後對提出的計算進行簡化,使之完全與我國規范相符。 -
Light gauge metal containers - definitions and determination of dimensions and capacities - part 1 : open - top cans iso 90 - 1 : 1997 ; german version en iso 90 - 1 : 1999
薄金屬板容器.定義和尺寸及容量測量方法.第1部分:頂
分享友人