limit temperature 中文意思是什麼

limit temperature 解釋
極限溫度
  • limit : n. 1. 界限，界線；邊界。2. 極限，限度；限制。3. 〈pl. 〉范圍，范域。4. 限價；限額；賭注限額；獵物限額。vt. 1. 限制，限定。2. 減少。adj. -able
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. The model of the itr between a1n and cu is built by using the acoustic mismatch model, amm and diffuse mismatch model, dmm. because there is a limit of roughness and temperature in amm and dmm, the data of the theory model that is directly built by amm and dmm is far from the experimental data. accordingly, with dmm and traditionary methods, the mathematics model is posed by contrast and analyses of the experiment data

    由於聲失配理論和散聲失配理論對溫度和粗糙度有很嚴格的要求，所以直接建模所得的理論數據與實驗數據有很大的差距，本文採用聲失配理論與傳統研究方法相結合，通過與實驗數據的分析擬合，提出了修正的數學模型，預測誤差有了大幅度的提高。
  2. The lower limit of temperature at which this occurs is known as the softening point or critical temperature.

    呈現這一性質的溫度下限稱為軟化點或臨界溫度。
  3. Therrnogravimetric analysis at heating rates 5, 10, 15 and 20 c / min was used to study the decomposition kinetics of the pdms / pma ipn in ni and in air by using tg and dtg, and the upper limit of the temperature was 700 c. it was found that ipn began to decomposite at 350 c. the process of the thermal degradation was multiple steps, the curve of the rate of thermal decomposition had two peaks, one of which lied between 400 c ~ 420 c and the other lied between 500 c ~ 540 c, the result corresponded to the components of ipn

    在熱分解動力學研究中，通過在兩種氣氛中，分別以5 、 10 、 15和20 min四種升溫速率條件下，採用tg - dtg聯動測試， ipn材料在350開始熱分解。熱分解速率存在兩個峰值，一個分解峰值在400 420之間，另一個在500 540之間，這與ipn結構中包含兩組分相對應，同時發現當緩慢升溫時，特別是在空氣氣氛中，兩個分解峰減弱，熱分解趨向於一個連續過程。
  4. The endurance limit is reduced for temperatures above room temperature.

    溫度高於室溫，持久極限則降低。
  5. How to set the upper limit and lower limit temperature

    怎樣設置溫度上限下限和化霜周期？
  6. In recent years, the colossal magneto - resistance effect in rare - earth manganite perovskites of the type lni. xaxmno3 ( where ln is rear - earth irons la2 +, nd2 +, p2 + ; a is alkaline earth iron ca2 +, sr2 +, ba2 + ) has attract considerable attention in scientific studies due to its potential application. however, the poor temperature dependence of mr and the low - temperature mr effect and the ideal mr only in high field severely limit their practical utility. in this work, we prepared manganite perovskite lai - xsrxmno3 and soft - magnetic ferrite materials fe2o3 and ( ni, zn ) fe2o4 by using sol - gel method separately

    近些年來，人們發現在鈣鈦礦錳氧化物ln _ （ 1 - x ） axmno _ 3 （ ln為la ， nd ， pr等稀土金屬元素； a為ca ， sr ， ba等堿土金屬元素）中具有磁電阻（ magnetoresistance ）效應，由於它在磁記錄，磁傳感器方面具有廣泛的應用前景，同時也向傳統的磁記錄材料提出了挑戰，因而引起了物理學界的廣泛關注。
  7. Comparison of calculation methods of limit of superheat temperature of liquid helium

    液氦極限過熱度計算方法比較
  8. In agreement with this concept is the additional experimental result that decreasing the mean hydrogen injection velocity increases the stability limit temperature.

    這一概念是與補充試驗的結果相符的，即降低氫的平均噴射速度使穩定性極限溫度增加。
  9. Then enter the state of setting lower limit temperature, using the key

    」鍵不放可連發，再按一次
  10. Set at least 2 seconds, the nixietube shows the upper limit temperature, and upper limit led lights, then using

    秒，進入設置狀態，這時「溫度上限」燈亮，數碼顯示器上顯示上限溫度，用「
  11. Set and hold it for at least 2 seconds, the controller displays the upper limit temperature, and upper limit led lights, then using the key

    秒，進入設置狀態，這時「溫度上限」燈亮，數碼顯示器上顯示上限溫度，用「
  12. The temperature field of the huge stream turbine rotor during free forging is numerically simulated with different process parameters. the purpose is to find out a set of optimum process parameters so that the temperature of the rotor center does not exceed the limit temperature of abnormal grain growth which is about 1100c

    對大型汽輪機轉子鍛造過程中的成形火次進行了溫度場的數值模擬和優化，得到了控制轉子鍛件心部溫度不超過1100的工藝參數，為實際生產解決混晶問題提供了參考數據。
  13. Plastics. thin sheets. determination of pliability limit temperature. looped test piece impact test

    塑料製品.薄板.柔韌性極限溫度測定
  14. Set lower limit temperature has been revised

    設置下限溫度已修改
  15. Set upper limit temperature has been revised

    設置上限溫度已修改
  16. Setting lower limit temperature

    設置下限溫度
  17. Setting upper limit temperature

    設置上限溫度
  18. Set upper limit temperature

    設置上限溫度
  19. Set lower limit temperature

    設置下限溫度
  20. Housing limit temperature

    外殼極限溫度
分享友人
分享到 Line

分享到臉書