linear tensile strength 中文意思是什麼

linear tensile strength 解釋
線性拉伸強度
  • linear : adj. 1. 線的，直線的。2. 長度的。3. 【數學】一次的，線性的。4. 【動、植】線狀的；細長的。5. 由線條組成的，以線條為主的，強調線條的。
  • tensile : adj 張力[拉力]的；抗張的；能伸長的。 tensile force 【物理學】張力。 tensile strain 【物理學】張應...
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. Type yg008 multi - filament yarn tensile strength tester is to determine the tensile strength and percentage elngation of raw silk and other linear materials ; print, output various data

    產品說明：本儀器用於測定生絲和其他線形材料的斷裂強度和伸長率，並列印輸出各項數據。
  2. Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great

    採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。
  3. Gloss. color. tensile strength. yield tensile strength flexural rigidity. flexural. elasticity. lmpact resistance. coating thichness. coating hardness. adhesion lmpact. abrasion. chemical resistance. cosfficicent of linear. thermal expan - sion thermal transmission properties. hdt

    光澤.顏色.拉伸強度.屈服抗拉強度.彎曲強度.彎曲模量.抗沖擊性.塗膜厚度.硬度.附著力.耐沖擊.耐磨耗性.耐化學性.熱膨脹系數.熱傳導系數.熱變形溫度
  4. Linear component gradient variation of aggregates improves 16 % of aggregates homogeneous distribution on bending strength ; parabolic component gradient variation does 8 %. gf is widely used as composite reinforcement due to low cast and excellent properties such as high tensile strength and high elastic modulus

    拋物線梯度不如線性梯度增強效果好，線性梯度變化比均勻分佈試件抗折強度提高了16 ，拋物線梯度提高了8 ；玻璃纖維的高抗拉強度及較高的彈性模量，提高了纖維混凝土復合材料的拉伸強度和彈性模量。
分享友人
分享到 Line

分享到臉書